Cisco Catalyst 3560-X User Manual

1-22
Catalyst 3750-X and 3560-X Switch Software Configuration Guide
OL-25303-03
Chapter 1 Overview
Default Settings After Initial Switch Configuration
• Dynamic ARP inspection is disabled on all VLANs. For more information, see Chapter 1,
“Configuring Dynamic ARP Inspection.”
• IGMP snooping is enabled. No IGMP filters are applied. For more information, see Chapter 1,
“Configuring IGMP Snooping and MVR.”
• IGMP throttling setting is deny. For more information, see Chapter 1, “Configuring IGMP Snooping
and MVR.”
• The IGMP snooping querier feature is disabled. For more information, see Chapter 1, “Configuring
IGMP Snooping and MVR.”
• MVR is disabled. For more information, see Chapter 1, “Configuring IGMP Snooping and MVR.”
• Port-based traffic
– Broadcast, multicast, and unicast storm control is disabled. For more information, see
Chapter 1, “Configuring Port-Based Traffic Control.”
– No protected ports are defined. For more information, see Chapter 1, “Configuring Port-Based
Traffic Control.”
– Unicast and multicast traffic flooding is not blocked. For more information, see Chapter 1,
“Configuring Port-Based Traffic Control.”
– No secure ports are configured. For more information, see Chapter 1, “Configuring Port-Based
Traffic Control.”
• CDP is enabled. For more information, see Chapter 1, “Configuring CDP.”
• UDLD is disabled. For more information, see Chapter 1, “Configuring UDLD.”
• SPAN and RSPAN are disabled. For more information, see Chapter 1, “Configuring SPAN and
RSPAN.”
• RMON is disabled. For more information, see Chapter 1, “Configuring RMON.”
• Syslog messages are enabled and appear on the console. For more information, see Chapter 1,
“Configuring System Message Logging and Smart Logging.”
• SNMP is enabled (Version 1). For more information, see Chapter 1, “Configuring SNMP.”
• No ACLs are configured. For more information, see Chapter 1, “Configuring Network Security with
ACLs.”
• QoS is disabled. For more information, see Chapter 1, “Configuring QoS.”
• No EtherChannels are configured. For more information, see Chapter 1, “Configuring
EtherChannels and Link-State Tracking.”
• IP unicast routing is disabled. For more information, see Chapter 1, “Configuring IP Unicast
Routing.”
• No HSRP groups are configured. For more information, see Chapter 1, “Configuring HSRP and
VRRP.”
• IP multicast routing is disabled on all interfaces. For more information, see Chapter 1, “Configuring
IP Multicast Routing.”
• MSDP is disabled. For more information, see Chapter 1, “Configuring MSDP.”
• Fallback bridging is not configured. For more information, see Chapter 1, “Configuring Fallback
Bridging.”

Cisco Catalyst 3560-X Specifications

General

Enclosure Type	Rack-mountable - 1U
Subtype	Gigabit Ethernet
Ports	48 x 10/100/1000 + 4 x SFP
Flash Memory	64 MB
Power Device	Internal power supply
Voltage Required	AC 120/230 V (50/60 Hz)
Operating System	Cisco IOS
Device Type	Switch
Performance	Switching capacity: 128 Gbps
Jumbo Frame Support	Yes
Routing Protocol	RIP-1, RIP-2, EIGRP
Remote Management Protocol	SNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, HTTP, HTTPS
Features	DHCP support, VLAN support, QoS, IPv6 support, Syslog
Compliant Standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad, IEEE 802.1w, IEEE 802.1x, IEEE 802.1s, IEEE 802.3ah, IEEE 802.1ag, IEEE 802.3at
Stacking	Stackable
Security Features	SSH, RADIUS, TACACS+
Management	CLI
Dimensions (H x W x D)	17.5 in
Operating Temperature	32 to 113 °F (0 to 45 °C)
Humidity	10 - 95% (non-condensing)