8.缝制时的故障、原因和对策 Troubles and corrective measures (sewing conditions)
9.选购品零件一览表 Table of the optional parts
Ⅱ.LK-1901A高速电子锁眼加固缝纫机的说明 Explanation of LK-1901A. computer-controlled
high-speed bartacking machjne
1.规格 Specifications
2.安装和运转准备 Installation of the sewing machine and preparation of the operation
3.靠布量的调节 Adjusting of the material closing amount
4.压脚提升量的调节 Adjustment of the lift of the work clamp foot
5.压脚压力的调节 Adjusting of the pressure of the work clamp unit
6.靠布动作的设定 Setting of the material closing operation
7.缝制图案的选定和确认 Selection and confirmation of the sewing patterns
Ⅲ.LK-1902A高速电子锁眼加固缝纫机的说明 Explanation of LK-1902A. computer-controlled
high-speed bartacking machjne
1.规格 Specifications
2.安装和运转准备 Installation of the sewing machine and preparation of the operation
3.上线的穿线方法 Installation of the sewing machine and preparation of the operation
4.缝制图案的选定和确认 Selection and confirmation of the sewing patterns
5.布压脚、送布底板的组装 Combination of the work clamp foot and the feed plate
Ⅳ.LK-1902A高速电子锁眼加固缝纫机的说明 Explanation of LK-1902A. computer-controlled
high-speed bartacking machjne
1.规格 Specifications
2.安装和运转准备 Installation of the sewing machine and preparation of the operation
3.机针和机线 Needle and thread
4.有关各种缝制模式 Various sewing modes
(1)缝制图案一览表 list of sewing patterns
(2)关于缝制图案的旋定和缝制宽度 Selection of the sewing pattern and the sewing width
5.纽扣抓脚的位置 Position of the button clamp jaw lever
6.布压脚底板的调整 Adjusting the feed plate
7.爪脚张开拨杆的调整 Adjusting the button clamp jaw lever
8.纽扣爪脚上升量的调整 Adjusting the lifting amount of the button clamp
9.压脚压力的调整 Adjustment of the pressure of the work clamp unit
10.挑线杆弹簧的调整 Adjusting of the wiper spring
11.纽扣挑起杆的调整 Installing the save button bar(accessory part)
12.按纽扣尺寸分类的机种 Model classification according to the button size
13.钉柄扣(选购品) Attaching the shank botton (optional)
(1).规格 Specifications
(2).针杆的调整 Adjusting the height of the needle bar
(3).布压脚底板的调整 Adjusting the feed plate base
(4).纽扣爪的调整 Adjusting the button clamp support
(5).落针的确认 Checking the needle entry point
(6).纽扣爪安装台和布压脚底板的调整 Adjusting the button clamp base and the feed plate
(7).纽扣压脚橡胶的调整 Adjusting the button support rubber
(8).纽扣压脚张开环的调整 Adjusting the button support link
Ⅸ
..................................59
.....................................................................................................61
..............................................................................................................................................63
........................................63
.....................................................................................64
...........................................................................64
.....................................................................65
..................................................................................65
........................................................66
...............................................................................................................................................67
........................................67
........................................67
.......................................................68
.............................................69
..............................................................................................................................................70
........................................70
............................................................................................................................70
..........................................................................................................71
............................................................................................................................71
.................................................................72
......................................................................................72
.........................................................................................................73
.................................................................................74
............................................................74
....................................................................74
................................................................................................75
......................................................................75
..........................................................76
.......................................................................................77
....................................................................................................................................................77
..............................................................................................................77
...............................................................................................................78
...............................................................................................................78
.....................................................................................................................79
................................................................79
.....................................................................................................80
......................................................................................................80
........
LK-190 0A零件样本
..............................................................................................................81-136
To Next Page
Loading...
