GRAPHTEC CE6000-120AP - Page 224

I-2
FAST key ....................................2-21
F command ..................................4-19
Feeding Method ..............................2-26
Feed Speed for Pre Feed ........................7-8
Force .......................................2-35
Force for cross cut ............................4-20
G
GP-GL Command .............................10-4
GP-GL STEP SIZE ............................10-4
Grit roller position guide ....................1-3, 2-16
Grit rollers ....................................1-3
H
Hold-down Force ..............................2-18
HP-GL Command .............................10-7
HP-GL MODEL EMULATED .....................10-7
I
I/F .........................................2-24
Indicator Lamp ...............................2-22
Initial Blade Control Position Adjust ...............6-12
Initial Feed ....................................7-6
Initial Setting .................................A-11
Interface .....................................8-2
Interface Setting Menu ..........................8-2
L
LANGUAGE SELECTION ........................9-2
Length of the Page .............................4-5
LENGTH UNIT .................................9-3
Length unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19, 2-52
Loading Media (Paper or Marking Film) .............2-7
Loading Roll Media .............................2-7
Loading Sheet Media ..........................2-14
M
Manual Position Adjust ..........................5-2
Marking mat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
MEDIA ......................................2-24
Media ........................................2-7
Media Change mode is off ......................4-11
Media Change mode is on ......................4-14
Media Cutter ..................................1-2
Media flange ..................................1-4
Media guide ...............................1-2, 1-4
Media guide bar ...............................1-4
MEDIA SENSOR ...............................9-4
Media sensors .............................1-3, 9-4
Media set lever ................................1-3
Media stocker .................................1-4
Media stopper .................................1-4
Menu Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2
Menu Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21
MENU lamp ..................................2-22
Menu Screen .................................2-24
Menu Tree ................................... A-5
Model ID Response ............................10-7
Move Away the Tool Carriage .....................3-5
Move in Steps Manually .........................3-3
Move the Tool Carriage and Media .................3-3
Moving the Pen While Raised or Lowered in Response to
the 'W' Command ...........................
10-6
N
Nomenclature .................................1-3
Normal menu .................................2-24
Number of pre feeds .......................... 2-46
O
Offset .......................................2-42
Offset Angle ..................................6-8
OFFSET FORCE ..............................6-14
Oil-based ballpoint pen ..........................1-2
Oil-based ballpoint pen plunger ...................1-2
ORIGIN key ..................................2-21
Origin Point ...................................3-7
Origin Point When HP-GL is Set ...................3-9
Overcut ......................................6-4
P
Page Length ................................ 2-44
Panel Cutting .................................4-16
Paper redy time ................................4-8
PAUSE/MENU key ............................2-21
Pause and Resume Cutting .....................3-12
Pen holder ....................................1-3
Pen station ...................................1-3
Plotter Environment .............................9-6
POSITION key ................................2-21
Power ......................................2-20
Power cable ...................................1-2
Power switch ..................................1-4
Pre feeds .....................................4-7
Printing the Setting of the Plotter ................12-13
Priority of Tool Condition Selection ................10-3
Push rollers ..............................1-3, 2-16
PUSH ROLLER SENSOR ........................9-5
Push Roller Sensors ............................9-5