11.3 Error Indication
178
Cannot change the lowest
noise frequency.
Change the noise sampling
speed.
Attempted to set the minimum noise fre-
quency at or above the maximum frequen-
cy (determined by the noise sampling
rate).
Increase the noise sampling rate setting, or set
the minimum noise frequency setting below the
maximum frequency.
See "4.6.2 Setting the Sampling Frequency
and Points" (p. 73)
"4.6.3 Setting the Minimum Noise Fre-
quency" (p. 74)
Cannot change the noise
sampling speed.
Change the lowest noise fre-
quency.
Attempted to set the maximum frequency
(determined by the noise sampling rate)
below the minimum noise frequency.
Decrease the minimum noise frequency set-
ting.
See "4.6.3 Setting the Minimum Noise Fre-
quency" (p. 74)
Cannot change the setting
under slave mode.
Attempted to set the clock, timer or clock
control settings with Slave mode enabled.
Clock, timer, and clock start/stop settings can-
not be changed while Slave mode is enabled.
See "8.3 Connecting Multiple 3390 (Synchro-
nized Measurements)" (p. 129)
Cannot change the setting in
3-phase measurement.
Attempted to select DC integration on a
non-1P2W channel.
DC integration is only available with 1P2W wir-
ing systems with an AC/DC current sensor con-
nected.
See "4.3.2 Setting the Integration Mode" (p. 56)
Cannot set DC when AC sen-
sor is connected.
Attempted to select DC integration on a
channel with an AC current sensor.
Not enough free capacity in
CF card.
Not enough space on CF card.
Delete unneeded files, or replace storage me-
dia (new CF card must be formatted).
Not enough free capacity in
USB memory stick.
Not enough space on USB drive.
Cannot create a file or folder.
Too many files or folders in root.
Possibly too many file or folders in the root
folder.
Delete unneeded files and folders, or specify
another folder as the file copy destination.
See "7.4 Saving Operations" (p. 107)
"7.10 File and Folder Operations" (p. 117)
CF card is not inserted. CF card not found.
Check that a CF card or USB drive is inserted.
See "7.1 Inserting and Removing Storage
Media" (p. 104)
USB memory stick is not con-
nected.
USB drive not found.
invalid character is used in
the folder name.
Attempted an operation with folder name
contains an invalid character, entered by
computer or malfunction.
Try again from the computer.
invalid character is used in
the file name.
Attempted an operation with file name
contains an invalid character, entered by
computer or malfunction.
Skip copying file named with
the invalid character.
A file name within the folder contains an
invalid character.
File(s) not copied.
Perform the copy operation from the computer.
Failed to access to the folder. Cannot access non-existent folder. -
Failed to access to the file. Cannot access non-existent file. -
Cannot create a file name au-
tomaticaly.
Automatic file name creation stopped.
Specify a different destination folder, or create
a new folder for saving, or delete unneeded
files, or replace storage media (new CF card
must be formatted).
See "7.10 File and Folder Operations" (p.
117)
Skip copying file named with
the invalid character.
Attempted to open a computer-created
folder that is not within the root folder.
Try again from the computer.
Skip copying folder not under
the root folder.
During folder copy, attempted to copy a
folder containing another folder.
File(s) not copied.
Perform the copy operation from the computer.
Cannot create a folder not un-
der the root folder.
Attempted to create a folder not in the root
folder.
Create a folder directly in the root folder.
See "7.10.1 Creating Folders" (p. 117)
Error display Cause Remedy
To Next Page
Loading...
