Honeywell MX7 Tecton User Manual

6 - 18
Switching to admin-
registry read failure
See the explanation of the “Registry read failure” above. AppLock is switching
into Admin mode. If a password has been configured, the prompt will be dis-
played and will not be dismissed until a valid password is entered.
LOG_PROCESSING
Switching to Taskbar-
ScreenMode
In administration mode, the taskbar is visible and enabled. LOG_EX
Switching to user
mode
The registry was successfully read and AppLock is starting the process to
switch to user mode.
LOG_PROCESSING
Switching to user-hot-
key press
The system is currently in admin mode and is now switching to user mode. The
switch occurred because of a hotkey press by the administrator.
LOG_PROCESSING
Taskbar hook failure AppLock is unable to control the taskbar to prevent the locked application from
re-enabling it.
LOG_ERROR
Taskbar hook OK AppLock successfully installed control of the taskbar. LOG_EX
Timeout looking for
app window
After the application is launched, AppLock must wait until the application has
initialized itself before proceeding. The application did not start successfully
and AppLock has timed out.
LOG_ERROR
ToUser after admin,
not at boot
The user mode switch is attempted when the device boots and after the admin-
istrator presses the hotkey. The mode switch is being attempted after a hotkey
press.
LOG_EX
ToUser after admin-
app still open
The switch to user mode is being made via a hotkey press and the administra-
tor has left the application open and has not made any changes in the configu-
ration.
LOG_EX
ToUser after admin-no
app or cmd line
change
If user mode is being entered via a hotkey press, the administrator may have
left the configured application open. If so, AppLock does not launch the appli-
cation again unless a new application or command line has been specified; oth-
erwise, it just locks it.
LOG_EX
Unable to move desk-
top
The desktop is moved when switching into user mode. This prevents them from
being visible if the application is exited and restarted by the timer. This error
does not affect the screen mode switch; processing continues.
LOG_ERROR
Unable to move task-
bar
The taskbar is moved when switching into user mode. This prevents them from
being visible if the application is exited and restarted by the timer. This error
does not affect the screen mode switch; processing continues.
LOG_ERROR
Unhook taskbar wnd-
proc failure
AppLock could not remove its control of the taskbar. This error does not affect
AppLock processing
LOG_ERROR
Unhook wndproc fail-
ure
AppLock could not remove the hook that allows monitoring of the application. LOG_ERROR
Unhooking taskbar In administration mode, the taskbar should return to normal operation, so Ap-
pLock’s control of the taskbar should be removed.
LOG_EX
Unhooking wndproc When the administrator leaves user mode, the device is fully operational; there-
fore, AppLock must stop monitoring the locked application.
LOG_EX
WM_SIZE adjusted This message denotes that AppLock has readjusted the window size. LOG_EX
X after Ctrl+L Processing the backdoor entry. LOG_EX
Ret from password
<#>
Return value from password dialog. LOG_EX
Decrypt data len <#> Length of decrypted password. LOG_EX
Window handle to
enumwindows=%x
The window handle that is passed to the enumeration function. This message
can be used by engineering with other development tools to trouble shoot ap-
plication lock failures.
LOG_EX
WM_WINDOW-
POSCHG adjust-
ed=%x
Output the window size after it has been adjusted by AppLock LOG_EX
Message Explanation and/or corrective action Level

Honeywell MX7 Tecton Specifications

General

Display diagonal	3.5 \
Display resolution	240 x 320 pixels
Display number of colors	-
Internal memory	0.256 GB
Internal memory type	RAM
Compatible memory cards	SD
Maximum memory card size	4 GB
Processor family	PXA 320
Processor frequency	0.806 GHz
GPS (satellite)	No
Operating system installed	Windows CE 6.0
Wi-Fi standards	802.11a, 802.11b, 802.11g
Bluetooth version	2.0+EDR
Headphone outputs	1
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	-30 - 50 °C
Operating relative humidity (H-H)	5 - 100 %
Battery capacity	2200 mAh
AC adapter output current	7.4 A
Product color	Black, Blue
Keyboard layout	Alphanumeric
Linear (1D) barcodes supported	Codabar, Code 128, Code 39, Code 93, EAN-13, GS1-128 (UCC/EAN-128), PLANET, Plessey, Telepen, Trioptic, U.P.C.
2D (matrix & stacked) barcodes supported	Aztec Code, Code 49, Data Matrix, MaxiCode, MicroPDF417, PDF417, QR Code

Weight and Dimensions

Depth	50 mm
Width	86 mm
Height	223 mm
Weight	595 g