[Switch3-GigabitEthernet2/0/0] quit
[Switch3] interface gigabitethernet 1/0/0
[Switch3-GigabitEthernet1/0/0] port hybrid untagged vlan 100
[Switch3-GigabitEthernet1/0/0] port vlan-stacking vlan 10 stack-vlan 100
[Switch3-GigabitEthernet1/0/0] quit
# Configure Switch4.
[Switch4] vlan 200
[Switch4-vlan200] quit
[Switch4] interface gigabitethernet 2/0/0
[Switch4-GigabitEthernet2/0/0] port hybrid tagged vlan 200
[Switch4-GigabitEthernet2/0/0] quit
[Switch4] interface gigabitethernet 1/0/0
[Switch4-GigabitEthernet1/0/0] port hybrid untagged vlan 200
[Switch4-GigabitEthernet1/0/0] port vlan-stacking vlan 20 stack-vlan 200
[Switch4-GigabitEthernet1/0/0] quit
Step 2 Configure an IGP on the MPLS backbone network so that the PE and P can interwork with each
other.
# Configure PE1.
<Quidway> system-view
[Quidway] sysname PE1
[PE1] interface loopback 1
[PE1-LoopBack1] ip address 1.1.1.9 32
[PE1-LoopBack1] quit
[PE1] vlan batch 30
[PE1] interface GigabitEthernet 3/0/0
[PE1-GigabitEthernet3/0/0]port hybrid pvid vlan 30
[PE1-GigabitEthernet3/0/0]port hybrid untagged vlan 30
[PE1-GigabitEthernet3/0/0] quit
[PE1] interface vlanif 30
[PE1-Vlanif30] ip address 172.1.1.1 24
[PE1-Vlanif30] quit
[PE1] ospf
[PE1-ospf-1] area 0
[PE1-ospf-1-area-0.0.0.0] network 172.1.1.0 0.0.0.255
[PE1-ospf-1-area-0.0.0.0] network 1.1.1.9 0.0.0.0
[PE1-ospf-1-area-0.0.0.0] quit
[PE1-ospf-1] quit
# Configure P.
<Quidway> system-view
[Quidway] sysname P
[P] interface loopback 1
[P-LoopBack1] ip address 2.2.2.9 32
[P-LoopBack1] quit
[P] vlan batch 30 60
[P] interface GigabitEthernet 1/0/0
[P-GigabitEthernet1/0/0] port hybrid pvid vlan 30
[P-GigabitEthernet1/0/0] port hybrid untagged vlan 30
[P-GigabitEthernet1/0/0] quit
[P] interface GigabitEthernet 2/0/0
[P-GigabitEthernet2/0/0] port hybrid pvid vlan 60
[P-GigabitEthernet2/0/0] port hybrid untagged vlan 60
[P-GigabitEthernet2/0/0] quit
[P] interface vlanif 30
[P-Vlanif30] ip address 172.1.1.2 24
[P-Vlanif30] quit
[P] interface vlanif 60
[P-Vlanif60] ip address 172.2.1.1 24
[P-Vlanif60] quit
[P] ospf
[P-ospf-1] area 0
[P-ospf-1-area-0.0.0.0] network 172.1.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[P-ospf-1-area-0.0.0.0] network 2.2.2.9 0.0.0.0
Quidway S7700 Smart Routing Switch
Configuration Guide - Ethernet 5 QinQ Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
317
To Next Page
Loading...
