[P-ospf-1-area-0.0.0.0] quit
[P-ospf-1] quit
# Configure PE2.
<Quidway> system-view
[Quidway] sysname PE2
[PE2] interface loopback 1
[PE2-LoopBack1] ip address 3.3.3.9 32
[PE2-LoopBack1] quit
[PE2] vlan batch 60
[PE2] interface GigabitEthernet 3/0/0
[PE2-GigabitEthernet3/0/0] port hybrid pvid vlan 60
[PE2-GigabitEthernet3/0/0] port hybrid untagged vlan 60
[PE2-GigabitEthernet3/0/0] quit
[PE2] interface vlanif 60
[PE2-Vlanif20] ip address 172.2.1.2 24
[PE2-Vlanif20] quit
[PE2] ospf
[PE2-ospf-1] area 0
[PE2-ospf-1-area-0.0.0.0] network 172.2.1.0 0.0.0.255
[PE2-ospf-1-area-0.0.0.0] network 3.3.3.9 0.0.0.0
[PE2-ospf-1-area-0.0.0.0] quit
[PE2-ospf-1] quit
After the configuration, OSPF relations are established between PE1, P, and PE2. Run the
display ospf peer command, and you can view that the status of the OSPF relations is Full. Run
the display ip routing-table command, and you can view that the PEs can learn the routes of
Loopback1 interfaces of each other.
Take the display on PE1 as an example.
[PE1] display ip routing-table
Route Flags: R - relied, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 9 Routes : 9
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.9/32 Direct 0 0 D 127.0.0.1 InLoopBack0
2.2.2.9/32 OSPF 10 1 D 172.1.1.2 Vlanif30
3.3.3.9/32 OSPF 10 2 D 172.1.1.2 Vlanif30
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.1.1.0/24 Direct 0 0 D 172.1.1.1 Vlanif30
172.1.1.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.1.1.2/32 Direct 0 0 D 172.1.1.2 Vlanif30
172.1.1.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
172.2.1.0/24 OSPF 10 2 D 172.1.1.2 Vlanif30
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
[PE1] display ospf peer
OSPF Process 1 with Router ID 1.1.1.9
Neighbors
Area 0.0.0.0 interface 172.1.1.1(Vlanif30)'s neighbors
Router ID: 172.1.1.2 Address: 172.1.1.2
State: Full Mode:Nbr is Master Priority: 1
DR: None BDR: None MTU: 1500
Dead timer due in 37 sec
Neighbor is up for 00:16:21
Authentication Sequence: [ 0 ]
Step 3 Configure basic MPLS functions, enable MPLS LDP, and establish LDP LSPs on the MPLS
backbone network.
# Configure PE1.
Quidway S7700 Smart Routing Switch
Configuration Guide - Ethernet 5 QinQ Configuration
Issue 01 (2011-07-15) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
318
To Next Page
Loading...
