Name: Juniper EX2200
Brand: Juniper
Rating: 5 (1 reviews)

To Next Page

To Previous Page

EX2200 switches provide:

•

Up to four uplink ports

•

12 (compact, fanless model), 24, or 48 built-in network ports with 10/100/100BASE-T

Gigabit Ethernet connectors

•

Virtual Chassis capability—You can connect up to four EX2200 switches (including

EX2200-C switches) together to form one unit that you manage as a single chassis,

called a Virtual Chassis, starting in Junos OS Release 12.2.

•

Power over Ethernet (PoE or PoE+) on all network ports (in PoE-capable models)

Uplink Ports

Each EX2200 switch except the EX2200-C switch model has four uplink ports that

support 1-gigabit small form-factor pluggable (SFP) transceivers for use with fiber

connections and copper connections.

Each EX2200-C switch has two dual-purpose uplink ports. Eachdual uplink port consists

of an RJ-45 port (in which you can connect a copper Ethernet cable) and an SFP port

(into which you can plug a transceiver). Only one of the ports can be active at a time. By

default, if you connect a copper Ethernet cable to the RJ-45 port, this port becomes the

active port provided that there is no connection made on the other port. If you plug a

transceiver into the SFP port, this port becomes the active port whether or not a copper

Ethernet cable is connected to the other port. You can change this default behavior by

explicitly configuring a media type—copper or fiber—for the dual-purpose port using the

media-type command. For more information, see Configuring the Media Type on

Dual-Purpose Uplink Ports (CLI Procedure).

You can use an SFP uplink port connection between EX2200 switches to interconnect

the switches into an EX2200 Virtual Chassis. You must explicitly configure the SFP port

as a VCP. See Setting an Uplink Port on an EX Series Switch as a Virtual Chassis Port (CLI

Procedure).

For information about the supported optical and copper interfaces, see “Pluggable

Transceivers Supported on EX2200 Switches” on page 26.

Console Port

Each EX2200 switch except the EX2200-C switch model has an RJ-45 console port that

accepts a cable with RJ-45 connector.

The EX2200-C switch has two console ports: an RJ-45 port and a Mini-USB Type-B port.

The RJ-45 console port accepts a cable with an RJ-45 connector and the Mini-USB

Type-B console port accepts a Mini-B plug (5-pin) connector to connect to the console

management device. The switch activates only one console port at a time, either the

RJ-45 console port or the Mini USB type-B console port. By default, the RJ-45 port is the

active console port and the Mini-USB Type-B port is the passive console port. You can

change the default setting of a console port using the port-type command. See Configuring

the Console Port Type (CLI Procedure).

Complete Hardware Guide for EX2200 Ethernet Switches

Juniper EX2200 Specifications

General

Throughput	77 Mpps
MAC address table	8000 entries
Jumbo frames support	Yes
Number of VLANs	1024
Networking standards	-
Switch type	Managed
SFP module slots quantity	4
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports quantity	48
Stackable	No
Product color	Black
Power consumption (typical)	100 W
Operating altitude	0 - 3048 m
Non-operating altitude	0 - 4877 m
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 45 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	10 - 85 %