EasyManua.ls Logo

Lenze 8400 StateLine C - Page 9

Lenze 8400 StateLine C
891 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Firmware 11.00 - DMS 8.0 EN - 10/2011 L 9
8400 StateLine C | Reference manual
Contents
6 I/O terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
6.1 Digital terminals
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
6.1.1 Change function assignment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
6.1.1.1 Using DI1 and DI2 as digital inputs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
6.1.1.2 Using DI1 and DI2 as frequency inputs
. . . . . . . . . . . . . . . . . . . . . . . . . . 259
6.1.1.3 Using DI1 as a counter input
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
6.1.2 Internal interfaces | System block "LS_DigitalInput"
. . . . . . . . . . . . . . . . . . . . . . . 266
6.1.2.1 Output of the encoder position of the DI1/DI2 frequency input
. . . 268
6.1.3 Internal interface | System block "LS_DigitalOutput"
. . . . . . . . . . . . . . . . . . . . . . . 272
6.2 Analog terminals
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
6.2.1 Parameterising analog input
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
6.2.1.1 Signal adaptation by means of characteristic
. . . . . . . . . . . . . . . . . . . . 277
6.2.2 Parameterising analog output
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
6.2.3 Internal interfaces | System block "LS_AnalogInput"
. . . . . . . . . . . . . . . . . . . . . . . 280
6.2.4 Internal interfaces | System block "LS_AnalogOutput"
. . . . . . . . . . . . . . . . . . . . . 280
6.3 Configuring exception handling of the output terminals
. . . . . . . . . . . . . . . . . . . . . . . . . . 281
6.4 User-defined terminal assignment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
6.4.1 Source-destination principle
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
6.4.2 Changing the terminal assignment with the keypad
. . . . . . . . . . . . . . . . . . . . . . . 284
6.4.3 Changing the terminal assignment with the »Engineer«
. . . . . . . . . . . . . . . . . . . 286
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

Table of Contents

Other manuals for Lenze 8400 StateLine C

Related product manuals