A-119
Appendices
CJ2 CPU Unit Software User’s Manual
A-3 Auxiliary Area
App
A-3-1 Read-only Area (Set by System)
A276
and
A277
--- Pulse Output 0
PV
Contain the number of pulses output from the corresponding
pulse output port.
8000 0000 to 7FFF FFFF hex (−2,147,483,648 to 2,147,483,647)
When pulses are being output in the CW direction, the PV is
incremented by 1 for each pulse.
When pulses are being output in the CCW direction, the PV is
decremented by 1 for each pulse.
PV after overflow: 7FFF FFFF hex
PV after underflow: 8000 000 hex
Lower 4 digits: A276/A278/A322/A324
Upper 4 digits: A277/A279/A323/A325
Cleared Cleared • Refreshed each
cycle during over-
seeing process.
• Refreshed when
INI(880) instruc-
tion is executed to
change the PV.
• Cleared when
Pulse Output
Reset Bit is
turned ON.
• Cleared when
pulse output is
started (when the
origin is not
defined).
• Refreshed when
PRV(881) instruc-
tion is executed to
read the PV or
status.
A278
and
A279
--- Pulse Output 1
PV
A280 A280.00 Pulse Output 0
Pulse Output
Status Flag
This flag will be ON when pulses are being output from pulse out-
put 0 according to an ORG(889), ACC(888), PLS2(887), or
IFEED(892) instruction and the output frequency is being
changed in steps (accelerating or decelerating).
OFF: Constant speed, ON: Accelerating/decelerating
Cleared Cleared • Refreshed each
cycle during over-
seeing process.
A280.01 Pulse Output 0
Overflow/Under-
flow Flag
This flag indicates when an overflow or underflow has occurred in
the PV of pulse output 0.
OFF: Normal, ON: Error
Cleared Cleared • Cleared when the
INI(880) instruc-
tion is executed to
change the PV.
• Refreshed when
an overflow or
underflow occurs.
A280.02 Pulse Output 0
Number of
Pulses Set Flag
ON when the number of output pulses for pulse output 0 has been
set with the PULS(886) instruction.
OFF: Not set, ON: Set
Cleared Cleared • Refreshed when
the PULS(886)
instruction is exe-
cuted.
• Cleared when
pulse output is
stopped.
A280.03 Pulse Output 0
Output Com-
pleted Flag
ON when the number of output pulses set with the PULS(886),
PLS2(887), or IFEED(892) instruction has been output through
pulse output 0.
OFF: Output not completed, ON: Output completed
Cleared Cleared Refreshed at the
start or completion
of pulse output in
independent mode.
A280.04 Pulse Output 0
Outputting
Pulses Flag
ON when pulses are being output from pulse output 0.
OFF: Stopped, ON: Outputting
Cleared Cleared Refreshed when
pulse output starts
or stops.
A280.05 Pulse Output 0
No-origin Flag
ON when the origin has not been determined for pulse output 0
and goes OFF when the origin has been determined.
OFF: Origin established, ON: Origin not established
Tur n ed ON
when oper-
ation starts.
Turned
ON when
opera-
tion
starts.
• Turned ON when
the pulse output
is reset.
• Turned ON when
an origin search
is started.
• Turned ON when
a limit input is
received and
clearing is set.
• Turned ON when
an overflow or
underflow occurs.
• Turned OFF when
an origin search
is completed.
• Turned OFF when
INI(880) instruc-
tion is executed to
change the PV.
Address
Name Function
Status
after mode
change
Status at
startup
Write timing/
Related flags, set-
tings
Words Bits
To Next Page
Loading...
