Omron NS User Manual

Appendices Appendix 6 Error Messages
A-21
N
S
-
Desi
g
ner O
p
eration Manual
Message Countermeasure
Downloading aborted. This Project includes
the file which name contains invalid charac-
ter. The characters that can be used are
alphanumeric characters (0 to 9, A to Z, a
to z), dollar sign ($), underscore (_), and.
Check and adjust project file.
There are limits on transferable file names. Check the
error message and use NS-Designer to adjust the file
name accordingly. There are similar limits on notation
for text files indirectly accessed.
End address is not set. Correctly designate the end address for replacement in
the Replace Dialog Box.
End page No. is out of range. Set a number
from 0 to 3999.
The end page number is 3,999. Set the end page
number to a number between 0 and 3,999.
End page No. is smaller than the start page
No.
Set the start page number so that it is smaller than the
end page number.
End sheet number is out of range. Set a
number from 0 to 9.
Sheet screen page numbers must be set in the range 0
to 9.
Set the sheet screen page number to a number be-
tween 0 and 9.
Error detected at NS hardware. (0x03a7) Contact your OMRON service representative.
Error occurred while writing to a flash
memory. Transmission failed.
Initialize data using Screen data region format on the
Data Initialization Tab Page under System Menu and
transfer the project.
Exceeding maximum/minimum limit. Set a number within the upper and lower limits.
Failed to create new folder. The folder could not be created because of insufficient
space on the hard disk.
Increase the available space on the hard disk and re-
peat the operation.
Failed to delete. Check to see if the specified category or file has been
opened by another application and repeat the opera-
tion. It is also possible that data has been corrupted.
Failed to export CSV file. The file could not be saved because of insufficient
space on the hard disk. Increase the available space
on the hard disk and repeat the operation.
Failed to get configuration information from
the printer for NS-Designer. Settings can-
not be performed for the printer.
This message is displayed when files containing infor-
mation for printer settings cannot be obtained. Reinstall
NS-Designer.
Failed to import CSV file. Check to be sure that the file to be imported is in CSV
format and repeat the operation.
Failed to open communications with the
PLC. CX-Server reported an unknown er-
ror.
Exit Screen Data Transfer of NS-Designer if this mes-
sage appears on the CX-Server when connecting to
the PLC to send the settings for the Path Through
PLC.
Failed to read file.
(Data Block (X) CSV File)
The specified CSV data file does not exist. Create a
CSV data file in the project folder.
Failed to read project file. The project file may be corrupted. If there is a backup
file, restore the project file using the backup file under
Project Maintenance - File - Project Maintenance.
Failed to register. Check to see if the specified category in the library has
been opened by another application and repeat the
operation. It is also possible that data has been cor-
rupted.
Failed to restore the project. Not have any free space left.
Change the Restore Destination or increase the free
space, and repeat the operation.
Failed to save file. The file could not be created because of insufficient
space on the hard disk. Increase the available space on
the hard disk and repeat the operation.

Omron NS Specifications

General

Power Supply	24 VDC
Display Size	5.7 to 12.1 inches (depending on the model)
Resolution	320 x 240 to 800 x 600
Touchscreen Type	Resistive
Display Type	TFT LCD
Communication Interfaces	RS-232C, RS-422/485, Ethernet, USB
Memory	Flash memory
Operating Temperature	0 to 50°C (depending on the model)
Storage Temperature	-20°C to 60°C
Protection Rating	IP65 (front panel)
Dimensions	Varies depending on the model
Weight	Varies depending on the model
CPU	Proprietary Omron CPU (performance varies depending on the model)