R&S ZNA67 - Page 1323

Command reference
R&S
®
ZNA
1323User Manual 1178.6462.02 ─ 20
Manual operation: See "Driving Mode" on page 632
7.3.14.12 [SENSe:]FREQuency...
The [SENSe:]... commands set frequency-related parameters, especially the mea-
surement and display ranges for the different sweep types. The frequency ranges for
the different instrument models are listed below; for more details refer to the data
sheet.
Table 7-17: Frequency ranges of R&S ZNA analyzers
Frequency settings Start, Stop Center Span
R&S ZNA26 100 kHz to 26.5 GHz >100 kHz to <26.5 GHz 1 Hz to 26.4999 GHz
R&S ZNA43 100 kHz to 43.5 GHz >100 kHz to <43.5 GHz 1 Hz to 43.4999 GHz
R&S ZNA50 100 kHz to 50 GHz >100 kHz to <50 GHz 1 Hz to 49.9999 GHz
R&S ZNA67 100 kHz to 67 GHz >100 kHz to <67 GHz 1 Hz to 66.9999 GHz
[SENSe<Ch>:]FREQuency[:CW]................................................................................... 1324
[SENSe<Ch>:]FREQuency:FIXed..................................................................................1324
[SENSe<Ch>:]FREQuency:COMPression:POINt.............................................................1324
[SENSe<Ch>:]FREQuency:COMPression:POWer:POINts................................................1325
[SENSe<Ch>:]FREQuency:COMPression:POWer:STARt.................................................1325
[SENSe<Ch>:]FREQuency:COMPression:POWer:STOP................................................. 1325
[SENSe<Ch>:]FREQuency:COMPression:SRCPort.........................................................1326
[SENSe<Ch>:]FREQuency:COMPression:RECeiver........................................................1326
[SENSe<Ch>:]FREQuency:CENTer............................................................................... 1326
[SENSe<Ch>:]FREQuency:CONVersion........................................................................ 1327
[SENSe<Ch>:]FREQuency<Pt>:CONVersion:ARBitrary...................................................1327
[SENSe<Ch>:]FREQuency:CONVersion:ARBitrary:PMETer<Pmtr>...................................1329
[SENSe<Ch>:]FREQuency<Pt>:CONVersion:AWReceiver[:STATe]...................................1330
[SENSe:]FREQuency:CONVersion:DEVice<Port>:NAME.................................................1330
[SENSe<Ch>:]FREQuency:CONVersion:GAIN:LMCorrection........................................... 1331
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FIXed<Stg>.............................................1331
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:FUNDamental......................................... 1332
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:IFPort..................................................... 1332
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOMultiplier<Stg>.................................... 1332
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:LOPort<Stg>........................................... 1333
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:MFFixed................................................. 1333
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFMultiplier.............................................1335
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:RFPort....................................................1335
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:STAGes.................................................. 1335
[SENSe<Ch>:]FREQuency:CONVersion:MIXer:TFRequency<Stg>...................................1336
[SENSe<Ch>:]FREQuency:IMODulation:CONVersion......................................................1336
[SENSe<Ch>:]FREQuency:IMODulation:LTONe............................................................. 1337
[SENSe<Ch>:]FREQuency:IMODulation:MSPectrum.......................................................1337
[SENSe<Ch>:]FREQuency:IMODulation:ORDer<Im>[:STATe].......................................... 1338
[SENSe<Ch>:]FREQuency:IMODulation:RECeiver..........................................................1338
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum:MORDer...........................................1338
[SENSe<Ch>:]FREQuency:IMODulation:SPECtrum[:STATe]............................................ 1339
SCPI command reference