Rohde & Schwarz ESW Series - Page 378

Network and Remote Operation
R&S
®
ESW
378User Manual 1177.6298.02 ─ 08
STATus:QUEStionable
15
14
13
12
11
10
9
8
7
6
5
4
3
0
1
2
not used
HCOPy in progress
CALibrating
15
14
13
12
11
10
9
8
7
6
5
4
3
0
1
2
not used
CALibration (=UNCAL)
POWer
LMARGin
LIMit
FREQuency
ACPLimit
15
14
13
12
11
10
9
8
7
6
5
4
3
0
1
2
ADJ UPPer FAIL
ADJ LOWer FAIL
ALT1 UPPer FAIL
ALT1 LOWer FAIL
ALT2 UPPer FAIL
ALT2 LOWer FAIL
not used
15
14
13
12
11
10
9
8
7
6
5
4
3
0
1
2
not used
15
9
8
7
6
5
4
3
0
1
2
7
6
5
4
3
0
1
2
7
6
5
4
3
0
1
2
Power On
User Request
Command Error
Execution Error
Device Dependent
Error
Query Error
Operation Complete
RQS/MSS
ESB
MAV
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
&
STAT:QUES:ACPLimit *)STATus:OPERation
STAT:QUES:LMARgin<n> *)
STAT:QUES:POWer *)
not used
IF_OVerload
OVERload
ESRESE
Output
Buffer
Error/ Event
Queue
PPE
ISTflag
SRE STB
SRQ
ALT3...11 LOWer/UPPer FAIL
TIME
15
14
13
12
11
10
9
8
7
6
5
4
3
0
1
2
LMARgin 1 FAIL
LMARgin 2 FAIL
LMARgin 3 FAIL
LMARgin 4 FAIL
LMARgin 5 FAIL
LMARgin 6 FAIL
LMARgin 7 FAIL
LMARgin 8 FAIL
not used
15
5
4
3
0
1
2
STAT:QUES:EXTended *)
not used
Sweep time too low
15
9
8
7
6
5
4
3
0
1
2
STAT:QUES:FREQuency *)
not used
OVEN COLD
LO UNLocked
External REFerence
STAT:QUES:LIMit<n> *)
LIMit 1 FAIL
LIMit 2 FAIL
LIMit 3 FAIL
LIMit 4 FAIL
LIMit 5 FAIL
LIMit 6 FAIL
LIMit 7 FAIL
LIMit 8 FAIL
DIQ
&
logic AND
logic OR
of all bits
TEMPerature
15
9
8
7
6
5
4
3
0
1
2
not used
STAT:QUES:TEMPerature *)
Frontend temp. error
INPut_overload
Range completed
SWEeping
MEASuring
Waiting for TRIGger
*) one register for each channel
EXTended
15
5
4
3
0
1
2
not used
STAT:QUES:TIME *)
INFO
15
5
4
3
0
1
2
STAT:QUES:EXTended:INFO *)
not used
INFO
MESSage
WARNing
ERRor
FATal
CACLR FAIL
SCAN results available
Threshold signal active
TRANsducer break
15
14
13
12
11
10
9
8
7
6
5
4
3
0
1
2
STAT:QUES:TRANsducer *)
Subrange 1
Subrange 2
Subrange 3
Subrange 4
Subrange 5
Subrange 6
Subrange 7
Subrange 8
Subrange 9
Subrange 10
not used
Subrange limit reached
RF Input 1
RF Input 2
Red font: Spectrum application only
Blue font: Receiver application only
I/Q Analyzer = Spectrum mode
Figure 14-2: Graphical overview of the R&S ESW status registers hierarchy
●
STB, SRE
The STatus Byte (STB) register and its associated mask register Service Request
Enable (SRE) form the highest level of the status reporting system. The STB pro-
vides a rough overview of the instrument status, collecting the information of the
lower-level registers.
●
ESR, SCPI registers
The STB receives its information from the following registers:
– The Event Status Register (ESR) with the associated mask register standard
Event Status Enable (ESE).
– The STATus:OPERation and STATus:QUEStionable registers which are
defined by SCPI and contain detailed information on the instrument.
●
IST, PPE
Remote Control Basics