SATO s84ex - Page 281

273
Table of command that can be specified as parameter
Classification
Command
Command name
The parameter can be replaced (underlined
part)
Font
<XU>
XU font
<XU>n～n
<XS>
XS font
<XS> n～n
<XM>
XM font
<XM> n～n
<XB>
XB font
<XB>1n～n
* Smoothing is fixed to valid
<XL>
XL font
<XL>1n～n
* Smoothing is fixed to valid
<OA>
OCR-A font
<OA>n～n
<OB>
OCR-B font
<OB>n～n
<$=>
Outline font print
<$=>n～n
<RD>
CG font
<RD>abb,ccc,ddd,n～n
Barcode
<B>
Barcode(Ratio 1:3)
<B>abbcccn～n
<D>
Barcode(Ratio 1:2)
<D>abbcccn～n
<D><d>
Barcode(HRI selection)
<D>abbcccn～n
<D>n～n
<BD>
Barcode(Ratio 2:5)
<BD>abbcccn～n
<BW>
Barcode print by ratio registration
<BW>aabbbn～n
<BI>
Exclusive for standard carton ID
GS1-128 (UCC/EAN)
<BI>aabbbcn～n
<BC>
CODE93
<BC>aabbbccn～n
<BG>
CODE128
<BG>aabbbn～n
<BF>
Bookland
<BF>aabbn～n
<BP>
POSTNET
<BP>n～n
<BL>
UPC-A barcode (without HRI)
<BL>abbcccn～n
<BL><d>
UPC-A barcode (HRI)
<BL>abbcccn～n
<d>n～n
<BM>
UPC-A barcode (with HRI)
<BM>abbcccn～n
2D code
<2D10>
PDF417
<DN>aaaa,n～n
<2D12>
Micro PDF417
<DN>n～n
* Only when binary mode is 0=Normal.
<2D20>
MaxiCode
<DN>aaaa,n～n
<2D30>
QR code (model 2)
<DS>k,n～n
<DN>aaaa,n～n
<2D31>
QR code (model 1)
<DS>k,n～n
<DN>aaaa,n～n
<2D32>
Micro QR code
<DS>k,n～n
<DN>aaaa,n～n
<2D33>
SQR code
<DS>k,n～n
<DN>aaaa,n～n
<2D50>
DataMatrix (ECC200)
<DN>aaaa,n～n
<2D51>
GS1 DataMatrix (ECC200)
<DN>aaaa,n～n
<BQ>
QR code
<BQ>abcc,(ddeeff,)g(hhhh)n～n
<BQ>abcc,(ddeeff,)n～n
<BV>
MaxiCode
<BV>a,b,c,ddddddddd,eee,fff,n～n
<BK>
PDF417
<BK>aabbcddeeffffg～g,h
<DC>
DataMatrix (ECC200) data
<BX>aabbccddeeefffghh
<DC>n～n
Control
<Q>
Print quantity
<Q>n～n
Intelligent
<IT>
Data sending form
<IT>aa,bb,n～n
[Important]
There are restrictions as follows with QR code, manual mode mixed:
- It is possible to replace normally when number of mix=1
- When the number of mix is bigger than 1, the print data that is acquired by the internal buffer recall command that is
specified before the QR code print command will be specified for replace for the number of mix.
- Recommend to use in auto mode when replacing the print data by internal buffer recall command.