Siemens simovert masterdrives - Page 1393

Parameter
Description Data Read/write
U793*
S.Multiplexer 4
2793
Source for the binectors of the multiplexer with 8
channels:
Index 1 : Signal selection Bit 0
Index 2 : Signal selection Bit 1
Index 3 : Signal selection Bit 2
Index 4 : Enable signal selection
index1: 0
Unit: -
Indices: 4
Type: L2 ,B
Menus:
- Parameter menu
+ Free blocks
- Upread/free access
Changeable in:
- Ready to switch on
- Operation enabled
U794*
S.Multiplexer 4
2794
The parameter defines the connector inputs of the
multiplexer with 8 channels:
Index 1 : Input 1
to
Index 8 : Input 8
index1: 0
Unit: -
Indices: 8
Type: L2 ,K
,K
Menus:
- Parameter menu
+ Free blocks
- Upread/free access
Changeable in:
- Ready to switch on
- Operation enabled
U795*
MechGearExEncod
2795
The parameter defines the mechanical transmission ratio
between the load side and the encoder side.
Index 1: Numerator = Load rotations
Index 2: Denominator = Encoder rotations
[Function diagram 333]
index1: 1
Min: 1
Max:
1048575
Unit: -
Indices: 2
Type: O4
Menus:
- Parameter menu
+ Free blocks
- Upread/free access
Changeable in:
- Ready to switch on
U796*
S.CoPosTrackEx
2796
Input signals for the free block "Start position of external
encoder"
Index 1: Source for the double word in which the
revolutions and overflow counters are stored in non-
volatile memory.
Index 2: Reserve
[Function diagram 333]
index1: 0
Unit: -
Indices: 2
Type: L2 ,K
,K
Menus:
- Parameter menu
+ Free blocks
- Upread/free access
Changeable in:
- Ready to switch on
- Operation enabled
U797*
S.BiPosTrackEx
2797
Definition of the input binectors for the free block "Start
position of external encoder"
Index 1: Reset overflow counter
- for linear axis to the value specified in U798.03
- for rotary axis to zero
Index 2: Reserve
[FD 333]
index1: 0
Unit: -
Indices: 2
Type: L2 ,B
Menus:
- Parameter menu
+ Free blocks
- Upread/free access
Changeable in:
- Ready to switch on
- Operation enabled
U798*
ConfLTrackExEnco
2798
Configuration of position tracking (motor
encoder/technology encoder):
Index 1 (0): 0=rotary axis, 1=linear axis
Index 2 (15): Number of overflows to be tracked for the
linear axis.
A maximum of 15 encoder overflows can be tracked.
Function diagrams -327- and -333-
Index 3 (0): Setting value of overflow counter for linear axis
index1: 0
Min: 0
Max: 15
Unit: -
Indices: 3
Type: O2
Menus:
- Parameter menu
+ Free blocks
- Upread/free access
Changeable in:
- Ready to switch on
n799
StatLTrackExEnco
2799
The parameter shows the status of position tracking for
the external encoder.
Index 1: Current status of the overflow counter of the
encoder
Index 2: Current status of the revolution counter of the
encoder
Index 3: Value transferred to position sensing
during acceleration
[FD 333]
Dec.Plc.: 0
Unit: -
Indices: 4
Type: I4
Menus:
- Parameter menu
+ Free blocks
- Upread/free access
233
Siemens AG 6SE7087-6QX70 (Edition AL)
SIMOVERT MASTERDRIVES Compendium Motion Control