February 2013
v
ColorQube® 9303 Family
Change History
Introduction
Change History
This page gives information on major changes to the service manual. Please go to the relevant
update.
• Bus Update May 2011
• Bus Update September 2011
• Bus Update June 2012
• Bus Update February 2013
Bus Update May 2011
The following procedures are updated:
• 12-460-00-171 to 12-462-00-171 HVF Bin 1 Position RAP
• 12L-171 Tri-Folder Not Detected RAP
• 94-549 Drum Runout Calibration Error RAP
• 99-081-00 to 99-112-00 PEST Error 2 RAP
• OF 5 Boot Up Failure RAP
• OF 16 POST Error RAP
• REP 12.19-171 Crease Roll Motor
• REP 12.27-171 BM Staple Heads
• REP 91.25 Drum and Front Drum Frame Assembly
• REP 91.29 Printhead
• REP 91.34 Drum Pulley
• Parts List updated
• GP 7 System Grounding Verification
• GP 35 Copy and Print Speeds
• GP 37 Post part Replacement Routines
• Wiring Diagram 12.10
• Principles of Operation (System Overview)
Bus Update September 2011
The following procedures are updated:
• 01E +12V Distribution RAP
• 01-525-00 +24V, +/-12V, +5V Short Circuit and Overload RAP
• 12G-110 LCSS PWB Damage RAP
• 19-300-00 to 19-310-00 Image Disk (HDD) Failure RAP
• 99-824-00 to 99-838-00 PEST Error 38 RAP
• OF 3 Unresponsive Machine RAP
• OF 16 POST Error RAP
• REP 1.9 Power Supply Unit
• REP 3.7 Single Board Controller PWB
• REP 3.9 NVM Module BWB and Battery
• REP 3.10 Power Distribution PWB
• REP 75.11 Tray 5 Elevator Tray Guides
• REP 91.25 Drum and Front Drum Frame Assembly
• REP 91.29 Printhead
• Parts List updated
• dC 967 Head to Drum Spacing Check
• Wiring Diagram 1.5 Power Supply Unit (5 of 5)
• Wiring Diagram 3.3 Single Board Controller PWB (3 of 3)
• Wiring Diagram 8.2 Media Path Driver PWB (2 of 5)
• Wiring Diagram 9.8 Marking Unit Heater PWB
Bus Update June 2012
The following procedures are updated:
• 12-024-00-171, 12-025-00-171 HVF Paddle Roller Position RAP
• 12-113-00-171, 12-114-00-171, 12-190-00-171 HVF BM Entry RAP
• 91-698-00 to 91-732-00 IOD Excessive Head Misalignment RAP
• 91-827-00 PQM Align Needed RAP
• 91-837-00 PQM Align Calibration Needed RAP
• 92-541-00, 92-570-00 Interrupt Storm Fault RAP
• 94-535-00 Drum Driver Command Curent Error RAP
• 94-538-00 to 93-540-00, 93-959-00 Lower Umbilical Thermal Error RAP
• 99-394-00 to 99-413-00 PEST Error 13 RAP
• 99-272-00 to 99-292-00 PEST Error 8 RAP
• 99-444-00 to 99-457-00 PEST Error 16 RAP
• 99-460-00 to 99-477-00 PEST Error 17 RAP
• OF 3 Unresponsive Machine RAP
• OF 12 Service Code RAP
• IQ 9 Deletions in the Process Direction RAP
• IQ 13 All Colours Uneven RAP
• REP 91.13 Stitch / Roll Motor
• REP 91.29 Printhead
• ADJ 12.2-171 Tri-Folder Paper Settings
• Parts List updated
• GP 15 Location and Function of PWB LEDs
• GP 37 Post Part Replacement Routines
• Principles of Operation
The following procedures are new:
• REP 91.37 Stitch / Roll Motor Lead Screws
Bus Update February 2013
This revision of the service manual was produced to meet the requirements for the;
• introduction of the dicovery 2.0 software platform, system software version
071.XXX.XX.XXX, GP 33.
• general update to the ColorQube 9303F procedures.
The following procedures are updated:
• Introduction. Remote Control Panel information
• SCP 3 Fault Analysis, warning added
• SCP 3 Wireless Connectivity RAP information added and GPs 41 to 49
• 12-473-00-171 to 12-478-00-171 Support Finger Position RAP
• 12D-171 Booklet Quality RAP
• 12G-110 LCSS PWB Damage RAP, new figure 1
To Next Page
Loading...
Need help?
General
