Local/Remote Run Selection.................................................. 189
Local/Remote Selection........................................................ 194
Low Voltage Directive......................................................... 236
L Protection Function .......................................................... 197
M
Magnetic Flux Compensation Capacity ..................................... 190
Main Circuit Connection Diagram ........................................ 36, 42
Main Circuit Terminal Functions...............................................39
Main Circuit Terminal Power Supply..........................................41
Main Circuit Terminals Connection............................................36
Main Circuit Terminal Wiring ............................................21, 241
Main Frequency Reference ......................................................49
Main Frequency Reference Input...............................................44
Maintenance Alarms ........................................................... 158
Master Speed Reference Lower Limit ....................................... 192
Maximum Motor Size Allowed (HP) ........................................ 181
Maximum Motor Size Allowed (kW)........................................ 182
Maximum Output Frequency.................................................. 193
MEMOBUS/Modbus Communication Error.............. 131, 132, 133, 140
MEMOBUS/Modbus Communications Test Mode Complete ........... 142
MEMOBUS/Modbus Communications Test Mode Error................. 142
MEMOBUS/Modbus Error Code ............................................ 202
MEMOBUS/Modbus Test Mode Complete................................. 132
Mid Output Voltage A ......................................................... 130
Minimum Output Frequency ............................................ 151, 152
Minimum Output Voltage ..................................................... 130
Minor Alarms ................................................................... 131
Minor Faults ..................................................................... 131
Modes ..............................................................................62
Momentary Power Loss Operation Selection ............................... 197
Monitor Output....................................................................44
Motor Does Not Operate When an External Run Command is Input ... 151
Motor
Does Not Operate When the RUN Button on the Digital Operator is
Pressed ........................................................................... 151
Motor Does Not Rotate ........................................................ 147
Motor Hunting and Oscillation Control Parameters ....................... 130
Motor Hunting Occurs When Operating With a Light Load.............. 150
Motor is Too Hot ............................................................... 148
Motor Line-to-Line Resistance ............................................... 193
Motor No-Load Current........................................................ 193
Motor Overload ........................................................... 132, 136
Motor Overload Protection Selection .................................. 197, 245
Motor Overload Protection Time ....................................... 197, 245
Motor Protection Function..................................................... 137
Motor Rated Current ..................................................... 193, 244
Motor Rated Slip................................................................ 193
Motor Rotates After the Drive Output is Shut Off ......................... 151
Motor Rotates Faster Than the Frequency Reference...................... 149
Motor Rotates in One Direction Only........................................ 152
Motor Stalls During Acceleration or With Large Loads .................. 149
Motor Stops During Acceleration or When a Load is Connected........ 152
Motor Wiring......................................................................41
Multi-Function Analog 1 (Terminal AM Monitor Selection)............. 196
Multi-Function Digital Inputs...................................................43
Multi-Function Digital Input Terminal S1 Function Selection ........... 194
Multi-Function Digital Input Terminal S2 Function Selection ........... 194
Multi-Function Digital Input Terminal S3 Function Selection ........... 194
Multi-Function Digital Input Terminal S4 Function Selection ........... 194
Multi-Function Digital Input Terminal S5 Function Selection ........... 194
Multi-Function Digital Output ..................................................44
Multi-Function Input Selection Error ........................................ 144
Multi-Function Input Setting Error........................................... 132
Multiple Drive Wiring ...........................................................41
Multi-Step Speed Reference................................................... 194
N
n1-02.................................................................. 130, 138, 200
n1 Hunting Prevention ......................................................... 200
n3: Overexcitation Braking.................................................... 200
n3-13.................................................................. 136, 137, 200
n Advanced Performance Set Up ............................................. 200
Noise From the Drive or Output Lines When the Drive is Powered On
..................................................................................... 150
No-Load Operation ...............................................................70
Normal Duty Ratings........................................................... 180
Number of Auto Restart Attempts............................................ 198
O
o1 Display Settings ............................................................. 200
o2-02........................................................................ 148, 200
o2-04........................................................................ 144, 200
o2-05.............................................................................. 200
o2 Multi-Function Selections ................................................. 200
o4-01.............................................................................. 201
o4-02.............................................................................. 201
o4-03........................................................................ 141, 201
o4-05.............................................................................. 201
o4-07.............................................................................. 201
o4-09.............................................................................. 201
o4-11.............................................................................. 201
o4 Maintenance Period......................................................... 201
oC ........................................................................... 132, 135
oFA01 ...................................................................... 132, 136
oH........................................................................... 132, 141
oH1 ......................................................................... 132, 136
oL1.......................................................................... 132, 136
oL2.................................................................... 132, 137, 151
oL3.................................................................... 132, 137, 141
o Operator Related Parameters................................................ 200
oPE ............................................................................... 144
oPE01 ...................................................................... 132, 144
oPE02 ...................................................................... 132, 144
oPE03 ...................................................................... 132, 144
oPE05 ...................................................................... 132, 144
oPE10 ...................................................................... 132, 144
oPE11 ...................................................................... 132, 145
Open-Chassis IP20 .......................................................... 28, 29
Operating with the Load Connected............................................71
Operation Errors .......................................................... 131, 132
Operator Connection Fault .................................................... 132
Operator Programming Errors ................................................ 144
oPr .......................................................................... 132, 137
Option Disconnected ........................................................... 132
Option Unit External Fault .............................................. 132, 134
Option Unit Fault ............................................................... 136
Oscillation or Hunting.......................................................... 151
Output Current .................................................................. 201
Output Current (A) ....................................................... 181, 182
Output Frequency............................................................... 201
Index
256
YASKAWA ELECTRIC SIEP C710606 31B YASKAWA AC Drive – J1000 Technical Manual
http://nicontrols.com
To Next Page
Loading...
