YOKOGAWA UP35A User Manual

xvi
IM 05P02D41-01EN
9.7.1 PV Event ........................................................................................................... 9-24
9.7.2 Time Event ........................................................................................................ 9-25
9.7.3 Local Event ....................................................................................................... 9-27
9.8
Setting the Operation in Segment Switching ......................................................................................9-28
9.8.1 Switching for continuation (JC=CONT) ............................................................. 9-28
9.8.2 Hold-on switching (JC=HOLD) .......................................................................... 9-30
9.8.3 Local-mode switching (JC=LOCAL) .................................................................. 9-32
9.8.4 Segment switching (the controller switches to a local setpoint when
the segment is completed after release) (JC=W.SL) ........................................ 9-34
9.9
Setting Starting time of program operation ......................................................................................... 9-35
9.10 Setting the Program Pattern Number Clearance ............................................................ 9-36
9.11
Program Pattern End Signal ............................................................................................................... 9-37
9.12 Editing the Prgram Pattern ............................................................................................. 9-38
9.12.1 Checking the Number of Remaining Segments ................................................ 9-38
9.12.2 Checking the Number of Segments in specified pattern ................................... 9-38
9.12.3 Copying a Program Pattern .............................................................................. 9-39
9.12.4 Adding and Deleting Segment in Program Patterns ......................................... 9-39
9.12.5 Deleting the Program Pattern ........................................................................... 9-40
9.12.6 List of the Error Code ........................................................................................ 9-40
9.13 SynchronizedProgramPatternOperation ..................................................................... 9-41
9.13.1 SynchronizedOperationDuringSwitchingBetweenSegments ....................... 9-41
9.13.2 SynchronizedOperationofProgramPatternProgression ................................ 9-44
Chapter 10 Output (Control and Retransmission) Functions
10.1 Setting Control Output Type ........................................................................................... 10-1
10.2 Setting Control Output Cycle Time ................................................................................. 10-5
10.3 Setting Limiter to Control Output .................................................................................... 10-6
10.4 Disabling Output Limiter in MAN mode .......................................................................... 10-7
10.5 Setting Velocity Limiter to Control Output ....................................................................... 10-8
10.6 Reducing 4-20 mA Current Output to 0 mA (Tight Shut Function) ................................. 10-9
10.7 Setting ON/OFF Control Hysteresis ............................................................................. 10-10
10.8 Canceling Offset of PV and SP (Manual Reset) ........................................................... 10-12
10.9 Setting Hysteresis and Dead Band for Heating/cooling Control Output ....................... 10-13
10.10 Setting Hysteresis and Dead Band for Position Proportional Control Output ............... 10-15
10.11 Setting Retransmission Output Terminal, Type, and Scales ......................................... 10-16
10.12 Setting Preset Output Value ......................................................................................... 10-18
10.12.1 Setting Output Value in RESET Mode (Preset Output) ................................... 10-18
10.12.2
Setting Output Value When Switched to MAN Mode (Manual Preset Output) ......... 10-19
10.12.3 Setting Output Value When Error Occurs (Input Error Preset Output)............ 10-20
10.13 Changing Current Output Range .................................................................................. 10-21
10.14 AdjustingMotor-operatedValvePosition(PositionProportionalOutput) ..................... 10-22
10.14.1 Setting Valve Operation Mode ........................................................................ 10-23
10.14.2 AdjustingValvePositionAutomatically ........................................................... 10-23
10.14.3 AdjustingValvePositionManually .................................................................. 10-24
10.14.4 Setting Valve Traveling Time (Estimating Type) .............................................. 10-25
10.14.5 Selecting Feedback Input (Resistor/Current) .................................................. 10-25
10.15 Using 15 V DC Loop Power Supply ............................................................................. 10-26
Chapter 11 Alarm Functions
11.1 Setting Alarm Type ..........................................................................................................11-1
11.2 Setting Number of Alarm Groups to Use .......................................................................11-14
11.3 Setting Hysteresis to Alarm Operation ..........................................................................11-15
Contents

YOKOGAWA UP35A Specifications

General

Brand	YOKOGAWA
Model	UP35A
Category	Controller
Language	English