Zebra MP7000 User Manual

Table of Contents v
AUX A-B (Stacked USB) ........................................................................................................ 2-56
POS ........................................................................................................................................ 2-56
12V DC ................................................................................................................................... 2-57
Chapter 3: Site Preparation and Installation
Introduction .................................................................................................................................... 3-1
Site Preparation ............................................................................................................................. 3-2
Ventilation and Spacing Requirements .................................................................................... 3-2
Service Access Requirements ................................................................................................. 3-2
Electrical Power Considerations .............................................................................................. 3-3
Grounding .......................................................................................................................... 3-3
Checkstand Preparation ........................................................................................................... 3-4
Liquid Spills and Moisture .................................................................................................. 3-4
Vertical Clearance .............................................................................................................. 3-4
Tools .................................................................................................................................. 3-4
Counter Cutout ................................................................................................................... 3-5
Ergonomics ........................................................................................................................ 3-5
Installing Components ................................................................................................................... 3-5
Quick Reference Installation Steps .......................................................................................... 3-5
Remove Existing Scanner Scale and Accessories .................................................................. 3-6
Unpacking MP7000 Scanner Scale Equipment ....................................................................... 3-6
Pre-Installation Notes ......................................................................................................... 3-7
Install the Scale Display ........................................................................................................... 3-8
Getting Started ................................................................................................................... 3-9
Installing ........................................................................................................................... 3-10
Cables and Connections ........................................................................................................ 3-10
Install the MX101 ................................................................................................................... 3-11
Install the MP7000 Scanner Scale ......................................................................................... 3-11
Checkstand Counter Cutouts and MP70XX Dimensions ................................................. 3-11
Cutout/Dimensions - MP70XX Short .......................................................................... 3-12
Cutout/Dimensions - MP70XX Medium ...................................................................... 3-14
Cutout/Dimensions - MP70XX Long ........................................................................... 3-16
Install the Sensormatic Coil Antenna ..................................................................................... 3-20
Install the Checkpoint Antennas ............................................................................................. 3-22
Horizontal Checkpoint Antenna ........................................................................................ 3-22
Vertical Checkpoint Antenna ............................................................................................ 3-23
Trim Kit Installation (If Required) ............................................................................................ 3-29
Chapter 4: Scale Calibration (For Models With a Scale)
Introduction .................................................................................................................................... 4-1
Scale Calibration Procedure (Scanner/Scale Configurations Only) ............................................... 4-2
Scale Configurations ................................................................................................................ 4-2
Step 1 - Electronic Entry into Calibration Mode ....................................................................... 4-3
Step 2 - Manual Entry into Calibration Mode ........................................................................... 4-3
Step 3 - Program Legal Parameters ........................................................................................ 4-4
Legal Scale Units (Unit Selection) - Kilograms or Pounds ................................................. 4-4
Important Notes ............................................................................................................ 4-4
Legal Scale Dampening Filter ............................................................................................ 4-5

Zebra MP7000 Specifications

General

Type	Built-in bar code reader
Sensor type	CMOS
Scanner type	1D/2D
Linear (1D) barcodes supported	Codabar, Code 128, Code 32, Code 39, Code 93, Discrete 2 of 5, EAN 128, EAN-13, EAN-8, GS1 DataBar, GS1 DataBar Expanded, GS1 DataBar Omnidirectional, GS1 Databar Limited, Interleaved 2 of 5, JAN, MSI, Plessey, Trioptic, UPC-A, UPC-E
2D (matrix & stacked) barcodes supported	Aztec Code, Data Matrix, Han Xin, Micro QR Code, MicroPDF417, PDF417, QR Code
Input voltage	90 - 264 V
Input frequency	47 - 63 Hz
Power source type	AC, RS-232, USB
Power consumption (standby)	3 W
Power consumption (typical)	5.5 W
Standard interfaces	RS-232, RS-485, USB
Connectivity technology	Wired
Keys quantity	4 keys
Product color	Black, Stainless steel
LED indicators	Yes
Image formats supported	BMP, JPEG
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	20 - 95 %
Harmonized System (HS) code	84716070

Weight and Dimensions

Depth	102 mm
Width	292 mm
Height	128 mm
Weight	5700 g