Figures
56
Figure 50: Bracket Holes ....................................................................................................................................................108
Figure 51: RKMT-J14 Bracket Holes ..................................................................................................................................109
Figure 52: Switch Orientations with the Front Panel Facing the Front of the Equipment Rack ..........................................109
Figure 53: Switch Orientations with the Rear Panel Facing the Front of the Equipment Rack...........................................110
Figure 54: Attaching the Handles to the RKMT-J14 Brackets ............................................................................................111
Figure 55: Attaching the RKMT-J14 Brackets to the Switch ...............................................................................................111
Figure 56: Installing the Switch in an Equipment Rack.......................................................................................................112
Figure 57: Installing the RKMT-J15 Bracket in the Equipment Rack ..................................................................................114
Figure 58: Loosening the Two Thumbscrews on the Front of the RKMT-J15 Bracket .......................................................114
Figure 59: Sliding Out the Bracket of the RKMT-J15..........................................................................................................115
Figure 60: Placing the GS980MX/10HSm Switch in the RKMT-J15 Bracket......................................................................115
Figure 61: Securing the GS980MX/10HSm Switch to the RKMT-J15 Bracket ...................................................................116
Figure 62: Sliding in the Bracket.........................................................................................................................................116
Figure 63: Tightening the Two Thumbscrews on the RKMT-J15 bracket...........................................................................117
Figure 64: Bracket Holes on the Switch..............................................................................................................................118
Figure 65: Switch Orientations in an Equipment Rack........................................................................................................119
Figure 66: Example of Attaching the Brackets to the Switch ..............................................................................................120
Figure 67: Installing the Switch in an Equipment Rack.......................................................................................................121
Figure 68: Positioning the GS980MX/28 or GS980MX/28PSm Switch on the Wall ...........................................................124
Figure 69: Positioning the GS980MX/10HSm, GS980MX/18HSm, GS980MX/52, or GS980MX/52PSm Switch
on the Wall........................................................................................................................................................125
Figure 70: Switch on the Wall with a Plywood Base ...........................................................................................................129
Figure 71: Installing the Switch on the Plywood Base ........................................................................................................130
Figure 72: Installing Two Brackets on the GS980MX/28 or GS980MX/28PSm Switch ......................................................132
Figure 73: Installing Four Brackets on the GS980MX/10HSm, GS980MX/18HSm, GS980MX/52 or
GS980MX/52PSm Switch.................................................................................................................................133
Figure 74: Securing the GS980MX/28 or GS980MX/28PSm Switch to the Plywood Base................................................134
Figure 75: Securing the GS980MX/10HSm, GS980MX/18HSm, GS980MX/52 or GS980MX/52PSm Switch
to the Plywood Base.........................................................................................................................................135
Figure 76: Marking the Locations of the Bracket Holes on a Concrete Wall.......................................................................137
Figure 77: Installing the Switch on a Concrete Wall ...........................................................................................................138
Figure 78: Installing the Retaining Clip ...............................................................................................................................143
Figure 79: Plugging in the AC Power Cord to the Switch ...................................................................................................145
Figure 80: Lowering the Power Cord Retaining Clip...........................................................................................................145
Figure 81: Plugging in the AC Power Cord to an AC Source..............................................................................................146
Figure 82: Management Cable Included with Switch..........................................................................................................150
Figure 83: VT-Kit3 Management Cable ..............................................................................................................................150
Figure 84: Management Workstation, VT-Kit3 Management Cable, and Switch................................................................151
Figure 85: Connecting the Management Cable to the Console Port ..................................................................................151
Figure 86: Switch Initialization Messages...........................................................................................................................158
Figure 87: Switch Initialization Messages (Continued) .......................................................................................................159
Figure 88: Switch Initialization Messages (Continued) .......................................................................................................160
Figure 89: Powering Off the Switch ....................................................................................................................................198
Figure 90: SHOW STACK Command.................................................................................................................................229
Figure 91: Installing an SFP Transceiver............................................................................................................................234
Figure 92: Positioning the SFP or SFP+ Handle in the Upright Position ............................................................................235
Figure 93: Connecting a Fiber Optic Cable to an SFP or SFP+ Transceiver .....................................................................235
Figure 94: Installing SP10TW Cables.................................................................................................................................237
Figure 95: GS980MX/10HSm .............................................................................................................................................244
Figure 96: GS980MX/18HSm .............................................................................................................................................245
Figure 97: GS980MX/28 .....................................................................................................................................................245
Figure 98: GS980MX/28PSm .............................................................................................................................................245
Figure 99: GS980MX/52 .....................................................................................................................................................246
Figure 100: GS980MX/52PSm ...........................................................................................................................................246
Figure 101: RJ-45 Socket Pin Layout (Front View).............................................................................................................252
To Next Page
Loading...
Need help?
General
