Barco DP2K SLP Series

Index
R5906848 /04 DP2K SLP Series402
ldm 1-3 - lls bank 6 not white point calibrated 373
ldm 1-3 – heatsink drain temperature sensor
open 366
ldm 1-3 – heatsink drain temperature sensor
shorted 366
ldm 1-3 – heatsink drain temperature too
high 366
ldm 1-3 – heatsink rectifier temperature sensor
open 366
ldm 1-3 – heatsink rectifier temperature sensor
shorted 366
ldm 1-3 – heatsink rectifier temperature too
high 366
ldm 1-3 – lls bank 4 current too high 365
ldm 1-3 – lls bank 4 drain power too high 368
ldm 1-3 – lls bank 4 drain voltage too high 364
ldm 1-3 – lls bank 4 temperature sensor
open 365
ldm 1-3 – lls bank 4 temperature sensor
shorted 365
ldm 1-3 – lls bank 4 temperature too high 365
ldm 1-3 – lls bank 5 current too high 365
ldm 1-3 – lls bank 5 drain power too high) 368
ldm 1-3 – lls bank 5 drain voltage too high 364
ldm 1-3 – lls bank 5 temperature sensor
open 365
ldm 1-3 – lls bank 5 temperature sensor
shorted 365
ldm 1-3 – lls bank 5 temperature too high 365
ldm 1-3 – lls bank 6 current too high 365
ldm 1-3 – lls bank 6 drain power too high) 368
ldm 1-3 – lls bank 6 drain voltage too high 365
ldm 1-3 – lls bank 6 temperature sensor
open 365
ldm 1-3 – lls bank 6 temperature sensor
shorted 365
ldm 1-3 – lls bank 6 temperature too high 365
ldm 1-4 - lls bank 7 not white point calibrated 373
ldm 1-4 - lls bank 8 not white point calibrated 373
ldm 1-4 – heatsink drain temperature sensor
open 367
ldm 1-4 – heatsink drain temperature sensor
shorted 367
ldm 1-4 – heatsink drain temperature too
high 367
ldm 1-4 – heatsink rectifier temperature sensor
open 367
ldm 1-4 – heatsink rectifier temperature sensor
shorted 367
ldm 1-4 – heatsink rectifier temperature too
high 367
ldm 1-4 – lls bank 7 current too high 366
ldm 1-4 – lls bank 7 drain power too high 368
ldm 1-4 – lls bank 7 drain voltage too high 366
ldm 1-4 – lls bank 7 temperature sensor
open 366
ldm 1-4 – lls bank 7 temperature sensor
shorted 366
ldm 1-4 – lls bank 7 temperature too high 366
ldm 1-4 – lls bank 8 current too high 366
ldm 1-4 – lls bank 8 drain power too high 368
ldm 1-4 – lls bank 8 drain voltage too high 366
ldm 1-4 – lls bank 8 temperature sensor
open 367
ldm 1-4 – lls bank 8 temperature sensor
shorted 367
ldm 1-4 – lls bank 8 temperature too high 367
ldm 1-6 – heatsink drain temperature sensor
open 363
ldm 1-6 – heatsink drain temperature sensor
shorted 363
ldm 1-6 – heatsink drain temperature too
high 363
ldm 1-6 – heatsink rectifier temperature sensor
open 363
ldm 1-6 – heatsink rectifier temperature sensor
shorted 363
ldm 1-6 – heatsink rectifier temperature too
high 363
ldm 1-6 – not configured (initialization
failure) 364
ldm 1-7 – 24v lcb voltage high 364
ldm 1-7 – heatsink rectifier temperature sensor
open 364
ldm 1-7 – heatsink rectifier temperature sensor
shorted 364
ldm 1-7 – heatsink rectifier temperature too
high 364
ldm 1–6 – not configured (invalid module
type) 363
ldm 1–7 – 24v LCB voltage low 364
ldm 1–7 – not configured (initialization
failure) 364
ldm 1–7 – not configured (invalid module
type) 364
lens - no lens parameter file has been
activated 344
lens focus position - requested target not
reached 307
lens horizontal shift position - requested target not
reached 309
lens motors - voltage too low 343
lens vertical shift position - requested target not
reached 310
lens zoom position - requested target not
reached 306
light pipe - temperature high 335
light pipe - temperature sensor open 336
light pipe - temperature sensor short 337
light pipe - temperature too high 335
light pipe fan - speed low 344
light sensor - no communication 296
light source - light is on, but smps is off 324
light source - not connected 305
light source - switching on the light source
failed 324
light source — the light source was switched off
due to an error 324
lls – bank 1 is off 347, 369–370
lls – bank 2 is off 348, 369, 371
lls – bank 3 is off 349, 370–371
lls – bank 4 is off 349, 370–371
lls – bank 5 is off 349, 370–371
lls – bank 6 is off 349, 370–371
lls – bank 7 is off 349, 370–371
lls – bank 8 is off 349, 370–371