D-Link xStack DGS-3620 Series - Chapter 45 IGMP Snooping Commands

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
544
Chapter 45 IGMP Snooping
Commands
config igmp_snooping [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {state [enable |
disable] | topology_changes_notification [ignore | process] | fast_leave [enable | disable] |
proxy_reporting {state [enable | disable] | source_ip <ipaddr>}}(1)
config igmp_snooping querier [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all]
{query_interval <sec 1-65535> | max_response_time <sec 1-25> | robustness_variable
<value 1-7> | last_member_query_interval <sec 1-25> | state [enable | disable] | version
<value 1-3>}(1)
config router_ports [<vlan_name 32> | vlanid <vlanid_list>] [add |delete] <portlist>
config router_ports_forbidden [<vlan_name 32> | vlanid <vlanid_list>] [add | delete] <portlist>
enable igmp_snooping
disable igmp_snooping
show igmp_snooping {[vlan <vlan_name 32> | vlanid <vlanid_list>]}
show igmp_snooping group {[vlan <vlan_name 32> | vlanid <vlanid_list> | ports <portlist>]
{<ipaddr>}}
config igmp_snooping rate_limit [ports <portlist> | vlanid <vlanid_list>] [<value 1-1000> |
no_limit]
show igmp_snooping rate_limit [ports <portlist> | vlanid <vlanid_list>]
create igmp_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipaddr>
config igmp_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipaddr> [add |
delete] <portlist>
delete igmp_snooping static_group [vlan <vlan_name 32> | vlanid <vlanid_list>] <ipaddr>
show igmp_snooping static_group {[vlan <vlan_name 32> | vlanid <vlanid_list>] <ipaddr>}
show igmp_snooping statistic counter [vlan <vlan_name 32> | vlanid <vlanid_list> | ports
<portlist>]
clear igmp_snooping statistics counter
show igmp_snooping forwarding {[vlan <vlan_name 32> | vlanid <vlanid_list>]}
show router_ports [vlan <vlan_name 32> | vlanid <vlanid_list> | all] {[static | dynamic | forbidden]}
config igmp access_authentication ports [all | <portlist>] state [enable {[auth_accounting |
auth_only | accounting_only]} | disable]
show igmp access_authentication ports [all | <portlist>]
45-1 config igmp_snooping
Description
This command is used to configure IGMP snooping on the switch.
Format
config igmp_snooping [vlan_name <vlan_name 32> | vlanid <vlanid_list> | all] {state [enable
| disable] | topology_changes_notification [ignore | process] | fast_leave [enable | disable] |
proxy_reporting {state [enable | disable] | source_ip <ipaddr>}}(1)
Parameters
vlan_name - Specifies the name of the VLAN for which IGMP snooping is to be configured.
<vlan_name 32> - Enter the VLAN name. The maximum length is 32 characters.
vlanid - Specifies the VLAN ID list.