EasyManuals Logo

Foundry Networks FESX User Manual

Foundry Networks FESX
820 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #677 background imageLoading...
Page #677 background image
Configuring BGP4
December 2005 © Foundry Networks, Inc. 21 - 105
rows under Refresh-Req indicate how many dynamic refreshes have been sent to and received from the neighbor.
The statistic is cumulative across sessions.
Closing or Resetting a Neighbor Session
You can close a neighbor session or resend route updates to a neighbor.
If you make changes to filters or route maps and the neighbor does not support dynamic route refresh, use these
methods to ensure that neighbors contain only the routes you want them to contain.
• If you close a neighbor session, the Layer 3 Switch and the neighbor clear all the routes they learned from
each other. When the Layer 3 Switch and neighbor establish a new BGP4 session, they exchange route
tables again. Use this method if you want the Layer 3 Switch to relearn routes from the neighbor and resend
its own route table to the neighbor.
• If you use the soft-outbound option, the Layer 3 Switch compiles a list of all the routes it would normally send
to the neighbor at the beginning of a session. However, before sending the updates, the Foundry Layer 3
Switch also applies the filters and route maps you have configured to the list of routes. If the filters or route
maps result in changes to the list of routes, the Layer 3 Switch sends updates to advertise, change, or even
withdraw routes on the neighbor as needed. This ensures that the neighbor receives only the routes you want
it to contain. Even if the neighbor already contains a route learned from the Layer 3 Switch that you later
decided to filter out, using the soft-outbound option removes that route from the neighbor.
FESX424 Router(config-bgp-router)# show ip bgp neighbor 10.4.0.2
1 IP Address: 10.4.0.2, AS: 5 (EBGP), RouterID: 100.0.0.1
Description: neighbor 10.4.0.2
State: ESTABLISHED, Time: 0h1m0s, KeepAliveTime: 0, HoldTime: 0
PeerGroup: pg1
Mutihop-EBGP: yes, ttl: 1
RouteReflectorClient: yes
SendCommunity: yes
NextHopSelf: yes
DefaultOriginate: yes (default sent)
MaximumPrefixLimit: 90000
RemovePrivateAs: : yes
RefreshCapability: Received
Route Filter Policies:
Distribute-list: (out) 20
Filter-list: (in) 30
Prefix-list: (in) pf1
Route-map: (in) setnp1 (out) setnp2
Messages: Open Update KeepAlive Notification Refresh-Req
Sent : 1 1 1 0 0
Received: 1 8 1 0 0
Last Update Time: NLRI Withdraw NLRI Withdraw
Tx: 0h0m59s --- Rx: 0h0m59s ---
Last Connection Reset Reason:Unknown
Notification Sent: Unspecified
Notification Received: Unspecified
TCP Connection state: ESTABLISHED
Byte Sent: 115, Received: 492
Local host: 10.4.0.1, Local Port: 179
Remote host: 10.4.0.2, Remote Port: 8053
ISentSeq: 52837276 SendNext: 52837392 TotUnAck: 0
TotSent: 116 ReTrans: 0 UnAckSeq: 52837392
IRcvSeq: 2155052043 RcvNext: 2155052536 SendWnd: 16384
TotalRcv: 493 DupliRcv: 0 RcvWnd: 16384
SendQue: 0 RcvQue: 0 CngstWnd: 1460

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Foundry Networks FESX and is the answer not in the manual?

Foundry Networks FESX Specifications

General IconGeneral
BrandFoundry Networks
ModelFESX
CategorySwitch
LanguageEnglish

Related product manuals