HP ProCurve 5400zl User Manual

queue4 < 0 to 100 > -- Specify min. bandwidth percentage for queue four
outgoing traffic. (p. 270)
■
■ queue5 < 0 to 100 > -- Specify min. bandwidth percentage for queue five
outgoing traffic. (p. 270)
■ additional options available...
■ broadcast-limit < 0 to 99 > -- Set a broadcast traffic percentage limit (p. 228)
■ dhcp-snooping -- Configure the port as trusted or untrusted (p. 230)
■ trust -- Configure trusted interfaces (p. 279)
■ disable -- Disable port(s) (p. 231)
■ enable -- Enable port(s) (p. 232)
■ flow-control -- Enable/disable flow control on the port(s) (p. 233)
■ gvrp -- Set the GVRP timers on the port (hundredths of a second) (p. 235)
■ join-timer < 20 to 75 > -- Set join timer value (centiseconds; default 20). (p. 246)
■ leaveall-timer < 500 to 3000 > -- Set leaveall timer value (centiseconds; default 1000). (p.
248)
■ leave-timer < 40 to 300 > -- Set leave timer value (centiseconds; default 300). (p. 248)
■ ip -- Apply the specified access control list to inbound packets on this INTERFACE list (p. 240)
■ access-group -- Apply the specified access control list to inbound packets on this INTERFACE
list (ASCII-STR) (p. 214)
■ direction < in > -- (p. 231)
■ source-lockdown -- Enable/disable IP source lockdown in global configuration mode (p. 276)
■ ipv6 -- Configure various IP parameters for the VLAN (p. 244)
■ access-group -- Apply a IPV6 ACl on the interface (ASCII-STR) (p. 214)
■ in -- Match inbound packets. (p. 238)
■ lacp -- Define whether LACP is enabled on the port, and whether it is in active or passive mode
when enabled (p. 247)
■ mode < Active | Passive > -- Define whether LACP is enabled on the port, and whether it
is in active or passive mode when enabled (p. 252)
■ link-keepalive -- Configure UDLD on port(s) (p. 248)
■ vlan -- Set vlan-id for tagged UDLD control packets. (VLAN-ID) (p. 282)
■ mdix-mode < mdi | mdix | autoMDIX > -- Set port MDI/MDIX mode (default: auto). (p. 250)
■ monitor -- Define either the port is to be monitored or not (p. 252)
■ all < In | Out | Both > -- Monitor all traffic. (p. 219)
■ mirror -- Mirror destination. (p. 251)
■ mirror_session_name -- Mirror destination name. (p. 251)
■ monitor_mirror_session_id < 1 to 4 > -- Mirror destination number. (p. 254)
■ no-tag-added -- Don't add VLAN tag for this untagged-port (p. 256)
■ name -- Set/unset a name for the port(s) (p. 254)
■ port-name -- Specify a port name up to 64 characters length. (ASCII-STR) (p. 263)
■ poe-allocate-by -- Control manual power over ethernet allocation (p. 261)
■ allocate_by < usage | class | value > -- Control manual power over ethernet allocation (p.
221)
■ poe-lldp-detect -- Enabling this feature causes the port to allocate power based on the
link-partner's capabilities via LLDP (p. 261)
■ poe_lldp_detect < disabled | enabled > -- Enabling this feature causes the port to allocate
power based on the link-partner's capabilities via LLDP (p. 260)
■ poe-value -- Maximum PoE allocation specified with a value in watts (p. 261)
■ poe_value < 1 | 2 | 3 | ... > -- Maximum PoE allocation specified with a value in watts (p. 260)
■ power-over-ethernet -- Enable/Disable per-port power distribution (p. 263)
■ priority < critical | high | low > -- Enable/Disable per-port power distribution (p. 265)
■ qinq -- Configure a port's type as customer-network or provider-network (p. 268)
■ port-type -- Configure qinq port-type (p. 263)
■ customer-network -- Configure qinq port-type as customer-network (p. 229)
205© 2009 Hewlett-Packard Development Company, L.P.
interfaceCommand Line Interface Reference Guide

HP ProCurve 5400zl Specifications

General

Brand	HP
Model	ProCurve 5400zl
Category	Switch
Language	English