EasyManuals Logo

HPE FlexNetwork 5510 HI Series Mpls Configuration Guide

HPE FlexNetwork 5510 HI Series
505 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #412 background imageLoading...
Page #412 background image
403
Step
Command
Remarks
session used to verify the
connectivity of the backup
PW.
Make sure the local discriminator
and remote discriminator
configured on the local PE are the
same as the remote discriminator
and local discriminator configured
on the remote PE, respectively.
Configuring BFD for a VPLS static PW
Step
Command
Remarks
1. Enter system view.
system-view
N/A
2. Enable BFD for MPLS.
mpls bfd enable
B
y default, BFD for MPLS is
disabled.
3.
Create a PW class and
enter PW class view.
pw-class
class-name
By default, no PW class is created.
To use BFD to verify connectivity of
a PW, you must create a PW class
for the PW and configure VCCV
settings in PW class view.
4.
Use BFD to verify PW
connectivity.
vccv bfd
[
template
template-name ]
By default, BFD is not used to verify
PW connectivity.
5. Specify the VCCV CC type.
vccv cc router-alert
By default, no VCCV CC type is
specified.
6. Return to system view.
quit
N/A
7. Enter VSI view.
vsi
vsi-name [
hub-spoke
]
N/A
8.
Configure the VSI to
establish static PWs and
enter VSI static view.
pwsignaling
static
N/A
9.
Configure a VPLS PW,
specify the created PW
class for it, and enter VSI
static PW view.
peer
ip-address
pw-id
pw-id
in-label
label-value
out-label
label-value
pw-class
class-name
[
hub
|
no-split-horizon
|
tunnel-policy
tunnel-policy-name ] *
By default, no VPLS PW is
configured.
10.
(Optional.) Configure the
local and remote
discriminators for the BFD
session used to verify PW
connectivity.
bfd discriminator local
local-id
remote
remote-id
By default, no local and remote
discriminators are configured.
Make sure the local discriminator
and remote discriminator
configured on the local PE are the
same as the remote discriminator
and local discriminator configured
on the remote PE, respectively.
11.
(Optional.) Configure a
static backup PW, specify
the PW class for the backup
PW, and enter VSI static
backup PW view.
backup-peer
ip-address
pw-id
pw-id
in-label
label-value
out-label
label-value
pw-class
class-name [
tunnel-policy
tunnel-policy-name ]
By default, no backup VPLS PW is
configured.
12.
(Optional.) Configure the
local and remote
discriminators for the BFD
session used to verify the
connectivity of the backup
PW.
bfd discriminator local
local-id
remote
remote-id
By default, no loca
l and remote
discriminators are configured.
Make sure the local discriminator
and remote discriminator
configured on the local PE are the
same as the remote discriminator
and local discriminator configured

Table of Contents

Other manuals for HPE FlexNetwork 5510 HI Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HPE FlexNetwork 5510 HI Series and is the answer not in the manual?

HPE FlexNetwork 5510 HI Series Specifications

General IconGeneral
BrandHPE
ModelFlexNetwork 5510 HI Series
CategorySwitch
LanguageEnglish

Related product manuals