EasyManuals Logo

HPE FlexNetwork 5510 HI Series Mpls Configuration Guide

HPE FlexNetwork 5510 HI Series
505 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #431 background imageLoading...
Page #431 background image
422
Step
Command
Remarks
7. Allow the local AS number
to appear in the AS_PATH
attribute of routes received
from the peer, and set the
maximum number of
repetitions.
peer
{ group-name | ip-address
[ mask-length ] }
allow-as-loop
[ number ]
By default, BGP discards
incoming route updates that
contain the local AS number.
8. Redistribute
remote site
routes advertised by the PE
into BGP.
import-route
protocol [ { process-id |
all-processes
} [
allow-direct
|
med
med-value
|
route-policy
route-policy-name ] * ]
By default, no routes are
redistributed into BGP.
9. (Optional.) Configure
filtering of advertised
routes.
filter-policy
{ acl-number |
prefix-list
prefix-list-name }
export
[ protocol
process-id ]
By default, BGP does not filter
advertised routes.
10. (Optional.) Configure
filtering of received routes.
filter-policy
{ acl-number |
prefix-list
prefix-list-name }
import
By default, BGP does not filter
received routes.
2. Configure a VPN site:
Step
Command
Remarks
1. Enter system view.
system-view
N/A
2. Enter BGP view.
bgp
as-number N/A
3. Configure the MCE as an
EBGP peer.
peer
{ group-name | ip-address
[ mask-length ] }
as-number
as-number
N/A
4. Enter BGP-VPN IPv4 unicast
address family view.
address-family ipv4
[
unicast
]
N/A
5. E
nable BGP to exchange
IPv4 unicast routes with the
peer.
peer
{ group-name | ip-address
[ mask-length ] }
enable
By default, BGP does not
exchange IPv4 unicast routes with
any peer.
6.
Redistribute the IGP routes
of the VPN into BGP.
import-route
protocol
[ { process-id |
all-processes
}
[
allow-direct
|
med
med-value
|
route-policy
route-policy-name ]
* ]
By
default, no routes are
redistributed into BGP.
A VPN site must advertise the
VPN network addresses it can
reach to the connected MCE.
Configuring IBGP between MCE and VPN site
To run IBGP between an MCE and a VPN site, you must configure a BGP peer for each VPN
instance on the MCE, and redistribute the IGP routes of each VPN instance on the VPN site.
1. Configure the MCE:
Step
Command
Remarks
1. Enter system view.
system-view
N/A
2. Enter BGP view.
bgp
as-number N/A
3. Enter BGP-VPN instance
view.
ip vpn-instance
vpn-instance-name
N/A
4. Configure an IBGP peer.
peer
{ group-name | ip-address
[ mask-length ] }
as-number
as-number
N/A
5. Enter BGP-VPN IPv4 unicast
address-family ipv4
[
unicast
]
N/A

Table of Contents

Other manuals for HPE FlexNetwork 5510 HI Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HPE FlexNetwork 5510 HI Series and is the answer not in the manual?

HPE FlexNetwork 5510 HI Series Specifications

General IconGeneral
BrandHPE
ModelFlexNetwork 5510 HI Series
CategorySwitch
LanguageEnglish

Related product manuals