IAI SEL User Manual

Change History
303
242
Controller no connection error. Communications cannot be established or an unsupported controller is connected. The probable causes are as follows: 㽲 It is a communication failure due to a break in or noise from the communication line. 㽳 The communication baud rate of the controller is not supported by the teaching pendant.
(The failure may be resolved by the controller power reconnection.)
㽴 The model not supported by the teaching pendant is connected. (Refer to Support Models.) The EMERGENCY STOP button of the teaching pendant is pressed. Non-supported controller is connected.
CTL Not Connected Emergency Stop Non-supported CTL is connected
DEE
DEF
DF0
Change History
noitpircseD noisiveR etaD noisiveR
2008.04
2008.11
2010.06
2011.01
First Edition
Second Edition
$GGHG³*DWHZD\)XQFWLRQ$VVRFLDWHG´
Third Edition
$GGHG³&RQQHFWLRQEHWZHHQ6(/7*DQGWKH&RQWUROOHU´
)RXUWK(GLWLRQ
³%HIRUH8VH´QHZO\DGGHGWRWKHILUVWSDJHDIWHUFRYHUSDJHLVRSHQHG
³%HIRUH8VH´LQ3JGHOHWHG
³6DIHW\3UHFDXWLRQV´LQ3JGHOHWHGDQG³6DIHW\*XLGH´DGGHGWR
WKHILUVWSDJHDIWHUFRQWHQWVSDJHV
³&KDQJH+LVWRU\´DGGHGWRWKHODVWSDJH
%DFNSDJHXSGDWHG&KDQJHLQDGGUHVVHVRI+HDG2IILFHDQGVDOHVRIILFHV
)LIWK(GLWLRQ
3DJH
3DJH
&DXWLRQQRWHVIRUDFWXDWRUPRYHPHQWRI/LQHDU6HUYR$FWXDWRU
/6$6116SXULRXV$EVROXWH7\SHDWKRPHUHWXUQDGGHG
 Sixth Edition
&RQWHQWVFKDQJHGLQ6DIHW\*XLGH
$GGHG;6(/565;6;5;'6;'&RQWUROOHU
2012.12 Seventh Edition
$GGHG=5XQLWDEVROXWHW\SHDEVROXWHUHVHWDQGWKH=5XQLWLQFUHPHQWDO
W\SHEDOOVFUHZVSOLQHVKDIWDGMXVWPHQWSURFHGXUH
 Eighth Edition
3DJHto 17&KDQJHDQGDGGLWLRQLQFRQQHFWLRQGUDZLQJUHODWHGWR
DGGLWLRQRI66(/&6$6(/&6DQG36(/&6
FRQQHFWRUFKDQJHG
 1LQWK(GLWLRQ
$GGHGLQIRUPDWLRQRQ77$DFWXDWRU
 (OHYHQWK(GLWLRQ
3DJHDQG&RUUHFWLRQPDGHWRPRGHOFRGHIRUFRQQHFWRUFRQYHUVLRQ
FDEOHVHWIRUFRQQHFWLRQWR6(/7*DQG,$/%7*6
3DJHWR'HVFULSWLRQVUHYLVHGUHJDUGLQJ73DGDSWHU
2014.02 Tenth Edition
3DJHWR$GGHG³$EVROXWH5HVHWRIWKHRUWKRJRQDOD[LV
36(/FRQWUROOHU´

IAI SEL Specifications

General

Protection Class	IP20
Communication	RS-232C
Control Method	PTP
Number of Axes	Up to 4 axes
Vibration Resistance	4.9 m/s² (0.5 G)
Humidity	20 to 85% RH (non-condensing)