Intermec CK30 - Page 438

Index
414 TE 2000
 5250 Terminal Emulation Programmer’s Guide
Protocols
3270, 123
Adaptive Poll, 212
Native, 123
RTC, 212
SST, 212
TCP/IP Direct Connect, 113
UDP Plus, 7, 105
upline, 107
VT/ANSI, 121, 122, 123
WTP, 7
Q
Quiet Zone
CONFIG.DAT option, 206
TE_SETTINGS.INI option, 225
R
RA order, 283
Radio, display annunciators
5055, 92
6400, 92
Radio baud rate s, 212
Radio comm, 141
2415, 2425, 2435A, 2455, 2475, 248X, 141
6400, 5055, 59XX, 17XX, 11XX, 142
disconnection value, 141
security ID, 142
use r auth entication, 141
Radio configuration number, CONFIG.DAT option, 197
Radio number
CONFIG.DAT option, 198
TE_SETTINGS.INI option, 219
Radio protocols , 212
Radio signal strength indicator. See RSSI
Radio test (802.11)
6400, 5055, 164
B SSID (Basic Service Set ID), 165
PRI (primary version), 165
RFLINK, 165
SEC (secondary version), 165
SNR (Signal-to-Noise Ratio), 165
SSID (Service Set ID), 165
TxRate, 165
Read Immediate command, 260
Read Input Fields command, 262
Read MDT Alternate command, 266
Read MDT Fields command, 264
Read Modified Immediate Alternate command, 261
Read Relay (#R) e xtended command, 331
Read Screen command, 267
Receive Only (#G) extended command, 310
Receiving, display annunciators
5055, 92
59XX, 92
6400, 92
Receiving data, display annunciators
11XX, 92
17XX, 92
Record Backspace key
11XX, 61
17XX, 56
2415, 19
2425, 23
2435A, 28
2455, 32
2475, 35
248X, 35
5055, 48
59XX, 52
6400, 39
bar code label, 358
CK30, 74
CK31, 79
CV60, 85
description, 12
Redundancy, 115
CONFIG.DAT option, 199
Relay (#R) extended commands, Set, Reset, Read, 331
Remap command, 234
Remapping characters, 240, 246
creating a macro, 235
EHLLAPI values, 235
key code table, 236
key or two-key sequence, 234
nesting , 236
Remapping keys, 234
per session, 236
Remote baud, 136
CONFIG.DAT option, 211
Remote display, 136
CONFIG.DAT option, 211
Remote type, 136
Renaming auto-login script files, 187
2415, 2425, 2435A, 2455, 2475, 248X, 188
5020, 700 Series, CK30, CV60, 188
59XX, 17XX, 11XX, 188
6400, 5055, 188
Repeat to Address order, 283
Reprogramming, flash memory, 252
Request/Response Header, 262
Resequencing
Read Immediate command, 260
Read Input Field command, 263
Start of Field command, 290
Start of Field order, 287
Start of Header order, 293
Reset key, 700 series, 67
Reset Relay (#R) extended command, 331
Reshow command, 5
Restart “x” command, 183
Restore Screen command, 273
Return AID key, 303
Return key, 700 se ries, 67
Return result
CONFIG.DAT option, 217
TE_SETTINGS.INI option, 231
Return Version (#V) extended command, 316