Jabiru j430 - Page 9

Aircraft Technical Manual
Jabiru Aircraft Pty Ltd
JTM001-5
J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants
This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.
ISSUE
1
2
3
4
5
Dated: 29th October 2014
Issued By: AS
Page: 9 of 298
Figure 144 – Air Duct Hard Point Reinforcement ..................................................................................................... 202
Figure 145 – Throttle Assy (Seat Mounted) .............................................................................................................. 205
Figure 146 – Throttle Assy (Panel Mounted) ............................................................................................................ 206
Figure 147 – Throttle Assy (Large Panel Mount)...................................................................................................... 206
Figure 148 – Control Cable End Fitting Installation .................................................................................................. 208
Figure 149 – Carburettor Heat Box .......................................................................................................................... 209
Figure 150 – Hot Air Duct Assy ................................................................................................................................ 210
Figure 151 – 2200 Exhaust System ......................................................................................................................... 212
Figure 152 – 3300 Exhaust System Type 1 ............................................................................................................. 212
Figure 153 – 3300 Exhaust System Type 2 ............................................................................................................. 213
Figure 154 – Cabin Heat Mixer Assembly ................................................................................................................ 214
Figure 155 – Cabin Heat Exchanger Assy ............................................................................................................... 215
Figure 156 – 2200 Engine Installation ...................................................................................................................... 216
Figure 157 – 2200 Engine Installation ...................................................................................................................... 216
Figure 158 – 2200 Engine Installation, Long Engine Mount ..................................................................................... 217
Figure 159 – J200 Family Engine Installation Type 1............................................................................................... 217
Figure 160 – J200 Family Engine Installation Type 2............................................................................................... 218
Figure 161 – In-Cabin Fuel System .......................................................................................................................... 220
Figure 162 – Fuel System Schematic – Type 1 ........................................................................................................ 220
Figure 163 – Fuel System Schematic – Type 2 ........................................................................................................ 221
Figure 164 – Fuel System Schematic – Type 3 ........................................................................................................ 221
Figure 165 – Fuel System Schematic – Type 4 ........................................................................................................ 222
Figure 166 – Schematic ............................................................................................................................................ 223
Figure 167 – Sample Fuel Line Details .................................................................................................................... 224
Figure 168 – Fuel Lines Showing Typical “U” Requiring Correction ........................................................................ 224
Figure 169 – Corrected Fuel Lines ........................................................................................................................... 225
Figure 170 – Header Tank Installation – Type 1 ...................................................................................................... 226
Figure 171 – Header Tank Installation – Type 2 (Sheet 1) ...................................................................................... 227
Figure 172 – Header Tank Installation – Type 2 (Sheet 2) ...................................................................................... 227
Figure 173 – Vented Fuel Cap Assy ......................................................................................................................... 229
Figure 174 – Single Line Fuel Tap ........................................................................................................................... 230
Figure 175 – Fuel Gauge – Electric Sender Installation ........................................................................................... 232
Figure 176 – Fuel Gauge – Electric Sender Assembly............................................................................................. 232
Figure 177 – Fuel Gauge – Sight Glass ................................................................................................................... 233
Figure 178 – Instrument Panel Layout Type 1 ......................................................................................................... 244
Figure 179 – Instrument Panel Layout Type 2 ......................................................................................................... 244
Figure 180 – Instrument Panel Layout Type 3 ......................................................................................................... 245
Figure 181 – Instrument Panel Layout Type 4 ......................................................................................................... 245
Figure 182 – Instrument Panel Mount Installation .................................................................................................... 246
Figure 183 – Pitot Assembly ..................................................................................................................................... 248
Figure 184 – Static Probe System Assembly ........................................................................................................... 249
Figure 185 – Pitot / Static Water Trap ...................................................................................................................... 250
Figure 186 – Pitot-Static System – Water Trap Locations ....................................................................................... 250
Figure 187 – Static System Test............................................................................................................................... 256
Figure 188 – Alternate Static Source Assy ............................................................................................................... 257
Figure 189 – Hall Effect Sensor Wiring (For Tach with Jabiru Logo on Face) ......................................................... 259
Figure 190 – Hall Effect Sensor Inst. (For Tach with Jabiru Logo on Face) ............................................................ 259
Figure 191 – Wiring Diagram Sheet 1. ..................................................................................................................... 264