Lenze i410 - Page 331

Address Name Default seng Category Data type Factor A M
0x402E:006
(P822.06)
End segment: PID setpoint 0.00 PID unit Sequencer I16 100 P -
0x402E:007
(P822.07)
End segment: Torque setpoint 100.0 % Sequencer I16 10 P -
0x402E:008 End segment: NetWordOUT2 0 Sequencer U16 1 P -
0x402E:009 End segment: Reserved 0 Sequencer U32 1 P -
0x402F
(P824.00)
End of sequence mode Keep running [0] Sequencer U8 1 P -
0x4030:001 ...
0x4030:016
(P830.01 ... 16)
Sequence 1: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4031
(P831.00)
Number of cycles sequence 1 1 Sequencer U16 1 P -
0x4032:001 ...
0x4032:016
(P835.01 ... 16)
Sequence 2: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4033
(P836.00)
Number of cycles sequence 2 1 Sequencer U16 1 P -
0x4034:001 ...
0x4034:016
(P840.01 ... 16)
Sequence 3: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4035
(P841.00)
Number of cycles sequence 3 1 Sequencer U16 1 P -
0x4036:001 ...
0x4036:016
(P845.01 ... 16)
Sequence 4: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4037
(P846.00)
Number of cycles sequence 4 1 Sequencer U16 1 P -
0x4038:001 ...
0x4038:016
(P850.01 ... 16)
Sequence 5: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x4039
(P851.00)
Number of cycles sequence 5 1 Sequencer U16 1 P -
0x403A:001 ...
0x403A:016
(P855.01 ... 16)
Sequence 6: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x403B
(P856.00)
Number of cycles sequence 6 1 Sequencer U16 1 P -
0x403C:001 ...
0x403C:016
(P860.01 ... 16)
Sequence 7: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x403D
(P861.00)
Number of cycles sequence 7 1 Sequencer U16 1 P -
0x403E:001 ...
0x403E:016
(P865.01 ... 16)
Sequence 8: Step 1 ... Step 16 Skip step [0] Sequencer I8 1 P -
0x403F
(P866.00)
Number of cycles sequence 8 1 Sequencer U16 1 P -
0x4040
(P820.00)
Start of sequence mode Restart sequencer [0] Sequencer U8 1 P -
0x4041:001 ...
0x4041:032
(P750.01 ... 32)
Parameter change-over: Parameter 1 ... Parameter
32
0x00000000 general IDX 1 PH -
0x4042:001 ...
0x4042:032
(P751.01 ... 32)
Parameter value set 1: Value of parameter 1 ... Value
of par
ameter 32
0 general I32 1 P -
0x4043:001 ...
0x4043:032
(P752.01 ... 32)
Parameter value set 2: Value of parameter 1 ... Value
of parameter 32
0 general I32 1 P -
* Default seng dependent on the model.
Appendix
P
arameter aribute list
331