FX3U Series Programmable Controllers
User's Manual - Hardware Edition
80
5 Version Information and Peripheral Equipment Connectability
5.2 Programming Tool Applicability
5.2.5 Cautions on write during RUN
In FX3U PLCs, write during RUN (program changes in the RUN mode) is enabled using the following
programming tools.
→ For the operating procedure of and cautions on write during RUN,
refer to the manual of the used programming tool.
Programming tools supporting write during RUN
• Japanese version
• English version
*1. Write during RUN is not possible with a SFC program.
*2. Write during RUN is not possible with a list program or a SFC program.
Programming tool PLC Version Remarks
GX Works2
*1
(SWDNC-GXW2-J)
FX3U
Ver. 1.07H or later
Writing in the instruction and device ranges during RUN is supported
in FX
3U and FX3UC PLCs earlier than Ver. 2.70.
Ver. 1.45X or later
Writing in the instruction and device ranges during RUN is supported
in FX
3U and FX3UC PLCs Ver. 2.70.
GX Developer
*2
(SWD5C-GPPW-J)
FX3U
Ver. 7.00A or later
Writing in the instruction and device ranges during RUN is supported
in FX2N PLCs Ver. 3.00.
Ver. 8.13P or later
Writing in the instruction and device ranges during RUN is supported
in FX
3UC PLCs earlier than Ver. 1.30.
Ver. 8.18U or later
Writing in the instruction and device ranges during RUN is supported
in FX
3UC PLCs earlier than Ver. 2.20.
Ver. 8.23Z or later
Writing in the instruction and device ranges during RUN is supported
in FX
3U and FX3UC PLCs earlier than Ver. 2.30.
Ver. 8.29F or later
Writing in the instruction and device ranges during RUN is supported
in FX3U and FX3UC PLCs earlier than Ver. 2.61.
Ver. 8.82L or later
Writing in the instruction and device ranges during RUN is supported
in FX
3U and FX3UC PLCs Ver. 2.61.
FX-PCS/WIN
*2
FX3U
Ver. 1.00 or later
Writing in the instruction and device ranges during RUN is supported
in FX2 PLCs Ver. 3.30.
Ver. 2.00 or later
Writing in the instruction and device ranges during RUN is supported
in FX
2N PLCs Ver. 1.00.
Ver. 4.20 or later
Writing in the instruction and device ranges during RUN is supported
in FX
2N PLCs Ver. 3.00.
Programming tool PLC Version Remarks
GX Works2
*1
(SWDNC-GXW2-E)
FX3U
Ver. 1.08J or later
Writing in the instruction and device ranges during RUN is supported
in FX
3U and FX3UC PLCs earlier than Ver. 2.70.
Ver. 1.48A or later
Writing in the instruction and device ranges during RUN is supported
in FX
3U and FX3UC PLCs Ver. 2.70.
GX Developer
*2
(SWD5C-GPPW-E)
FX3U
Ver. 7.00A or later
Writing in the instruction and device ranges during RUN is supported
in FX2N PLCs Ver. 3.00.
Ver. 8.18U or later
Writing in the instruction and device ranges during RUN is supported
in FX
3UC PLCs earlier than Ver. 2.20.
Ver. 8.24A or later
Writing in the instruction and device ranges during RUN is supported
in FX
3U and FX3UC PLCs earlier than Ver. 2.30.
Ver. 8.29F or later
Writing in the instruction and device ranges during RUN is supported
in FX3U and FX3UC PLCs earlier than Ver. 2.61.
Ver. 8.82L or later
Writing in the instruction and device ranges during RUN is supported
in FX3U and FX3UC PLCs Ver. 2.61.
FX-PCS/WIN-E
*2
FX3U
Ver. 1.00 or later
Writing in the instruction and device ranges during RUN is supported
in FX
2N PLCs Ver. 1.00.
Ver. 3.10 or later
Writing in the instruction and device ranges during RUN is supported
in FX
2N PLCs Ver. 3.00.
To Next Page
Loading...
Need help?
General
