MultiTrode MultiSmart - Page 258

MultiSmart Installation & Operation Manual
Index
1
10 Sensor Probe .............................................................. 43
A
ACROMAG Ethernet Units ............................................. 102
ADAM Ethernet Units ..................................................... 101
Add PSU & Battery Backup .............................................. 48
Adding or Deleting Groups ............................................... 91
Advanced Analog Input Options ....................................... 99
Advanced Configuration ................................................. 212
Advanced Digital Input Options ......................................... 96
Advanced Settings ........................................................... 71
Alarm Activation/Deactivation points ................................. 85
Alternation and Grouping .................................................. 89
Analog Inputs ............................................................. 44, 98
Analog Inputs for Flow Measurement ............................. 162
Analog Level Compare ................................................... 115
Analog Level Sensor Configuration................................. 112
Analog Output for use with a VFD Drive ......................... 188
Analog Outputs................................................... 45, 54, 123
Assigning a Name to Digital Inputs ................................. 139
B
Backup and Restoration of Settings ................................ 209
Backup Level Devices & Failover ................................... 113
C
Calculating Efficiency ..................................................... 147
CAN Bus .......................................................................... 49
CAN Bus Settings ............................................................. 50
CAN Status LEDs ............................................................. 52
Cellular Modem (PumpView) Setup .................................. 56
Changing Group Alternation ............................................. 91
Changing the order of Pumps ........................................... 91
Communication Channel Settings ................................... 180
Communication Protocols ....................................... 170, 184
Communications Redundancy ........................................ 182
Communications Screen................................................. 170
Configure General Flow Settings .................................... 161
Configuring Faults .......................................................... 142
Configuring General Faults ............................................. 121
Configuring I/O, Fault & Level Devices ............................. 93
Configuring Motor Protection Faults ................................ 141
Configuring Remote and Local Level .............................. 114
Configuring the datalogger ............................................. 159
Configuring the Setpoints of Profiles ............................... 130
Connecting the Display ............................................... 33, 45
CPU Board .................................................................34, 45
CT Value Configuration .................................................. 141
Current Inputs .................................................................. 54
Current Inputs used in Motor Protection ......................... 146
Customizing the Display ................................................ 204
D
Data Logger ..................................................................... 76
Datalogger ..................................................................... 151
Decommissioning Pumps ................................................ 92
Default Pump and Alarm Setpoints .................................. 83
Default Wiring for Pump Controller Board
Default 2 – 10 Sensor Probe and 3 Pumps .......................... 37
Default 3 – 4-20mA Level/Control and 2 pumps ................... 38
Default 4 – 4-20mA Level/Control and 3 Pumps .................. 39
Default Wiring for Pump Controller Board
Default 1 – 10 Sensor Probe and 2 Pumps .......................... 36
Delay Fail (No Flow) Fault Setup ................................... 120
Digital Inputs ......................................................... 42, 93, 97
Digital Inputs for Flow Measurement .............................. 162
Digital Outputs ............................................................... 124
Digital Tag ....................................................................... 80
Digital Volt-Free Outputs .............................................44, 53
DNP3 Point Configuration ....................................... 171, 172
DSP Board .................................................................34, 46
DSP Status LEDs ............................................................ 47
DuoProbe Level Sensor Configuration ........................... 108
E
Enable/Disable Alarms ..................................................... 86
Enabling Insulation Resistance Testing (IRT) ................. 144
Enabling Logic Files ....................................................... 203
Enabling New Modules .................................................. 206
Ethernet Port ................................................................... 45
Exporting and Importing DNP3 / MODBUS Points List ... 177
External Digital & Analog Modules ................................... 99
F
Fault Inputs ...................................................................... 93
Fault Message Glossary ................................. 215, 219, 220
Fault Module .................................................................... 76
Faults - Configuration.............................................. 116, 123
Faults Screen .................................................................. 18
Fill / Empty (Charge / Discharge) ..................................... 83
Filtering History Data ..................................................... 156
Flash Memory Card ......................................................... 46
Flow ............................................................ 61, 76, 161, 163
Page 258 of 260 MultiSmart_IO_Manual_R20