NEC Univerge SV8100

To Next Page

To Previous Page

Issue 4.1 UNIVERGE SV8100

4 - 32 Installing the SV8100 Blades

One PZ-VM21 daughter board providing InMail can be installed per system.

Refer to the Univerge UNIVERGE SV8100 System InMail System Guide for

complete set-up information.

Figure 4-8 Installing the PZ-VM21

Main Page

Default Chapter3
- Table of Contents3
Regulatory19
Chapter 2 SV8100 System Specifications23
Chapter 1 Introduction to SV810023
- General Information23
- Section 1 General Information23
- System Block Diagram37
- Maximum System Capacities41
Chapter 3 Installing the SV8100 Chassis69
- Section 1 General Information69
- Installing the Chassis69
- Battery Connection124
- Remove and Install Cooling Fan145
  - CHS2U Chassis145
    - Install Cooling Fan145
    - Remove Cooling Fan145
Chapter 4 Installing the SV8100 Blades149
- Section 1 General Information149
  - Slot Locations149
- Installation151
Station Blades192
- CD-8DLCA/CD-16DLCA (Digital Station Interface)192
- PZ-8DLCB (Digital Station Daughter Board)197
- Trunk Blades215
Optional Blades248
- CD-PVAA (Conference Bridge) (Future Enhancement)249
Chapter 5 Installing DT300/DT700 Series (DTL/ITL) Digital and IP259
- General Description259
- DT300 Series Digital Multiline Terminals265
DT700 Series IP Multiline Terminals273
- IP Multilineterminals273
Install Multiline Terminals281
- Connecting the DT300 Series Multiline Terminal to the System281
- Applying Power to the DT700 Multiline Terminals282
- Connecting the IP Multiline Terminal to the Network and PC283
- Adjusting the LCD on the Multiline Terminal284
- Installing Line Key Kit (12LK-L KIT)285
- Installing the Directory Card on the Multiline Terminal291
- Installing a Numbered Keypad on the Multiline Terminal292
Optional Handsets329
- ITL / DTL PTM Handset329
- ITL / DTL PTT Handset329
- UTR-1-1 USB Handset330
  - USB Connection330
  - Wall Mounting331
Bluetooth Cordless Handset332
- Bluetooth Cordless Handset (BCH) Interface332
- Selecting a Location333
- Controls and Indicators334
- Installing the Bluetooth Cordless Handset336
Bluetooth Hub Adapter346
- Installing the BHA-L UNIT346
- Pairing a Bluetooth Device and Multiline Terminal (Bluetooth Installed)348
- Single Line Telephone351
  - Installing the SLT Adapter351
  - Wall-Mounting the SLT Adapter352
Chapter 6 Installing SV8100 Optional Equipment355
- General Information355
- Pgd(2)-U10 Adp355
- Background Music364
  - Installing Background Music364
- Door Box365
  - Installing a Door Box365
- External Paging369
  - External Page369
  - Installing an External369
- External Paging and Door Box371
  - External371
  - Door Box /External Page Relay Contacts372
    - Connecting a Contact Relay Device to a Door Box/External Page372
    - Relay372
External Recording System/External Ringer373
- External Recording System or External Ringer373
- Installing an External Recording System or External Ringer374
- Programming375
Music Sources378
- Music on Hold378
- Installing External Music on Hold378
Night Mode Selection381
- Night Mode Selector Switch381
- Connecting a Night Mode Selector Switch381
Section 10 Telephone Labeling381
- Removing the Faceplate382
- Replacing the Faceplate382
Section 11 Telephone Adapters383
- Using Adapters383
- In-Line Power Adapter (ILPA-R)383
  - Conditions384
  - Installation385
- Ada-L Unit387

NEC Univerge SV8100 - Page 180

Table of Contents

Other manuals for NEC Univerge SV8100

Related product manuals