Index-3
CJ2 CPU Unit Software User’s Manual
P
Parameter Area ............................................................. 2-3
Parameter Date ........................................................... 10-5
parameter file ................................................................ 7-8
Peripheral Services ..................................................... 9-30
peripheral servicing ....................................................... 3-5
backup servicing ..................................................... 3-5
communications port servicing ................................ 3-5
event servicing for CPU Bus Units .......................... 3-5
event servicing for Special I/O Units ....................... 3-5
file access servicing ................................................ 3-5
online editing servicing ............................................ 3-5
peripheral USB port service .................................... 3-5
serial port service .................................................... 3-5
PLC Backup Tool ........................................................ 7-14
PLC name ................................................... 2-3, 4-4, 10-60
PLC Setup ....................................................... 4-4, 4-8, 9-2
background execution settings .............................. 9-12
Basic I/O Unit rack response times ....................... 9-21
Comms Instructions Settings in FB ....................... 9-13
Communications Settings ...................................... 9-23
CPU processing mode .......................................... 9-30
CPU Unit Settings ................................................... 9-8
cycle time .............................................................. 9-15
Disable SIOU Cyclic Refresh ................................ 9-19
Execute Process ..................................................... 9-8
Execution Setting .................................................... 9-7
FINS Protection ..................................................... 9-31
Forced Status Hold Bit Startup Hold Setting ........... 9-5
I/O Module ............................................................. 9-32
IOM Hold Bit Startup Hold Setting ........................... 9-6
Operating Mode ....................................................... 9-7
Peripheral Services ............................................... 9-30
power OFF detection delay time ........................... 9-17
power OFF interrupt disabled ................................ 9-18
rack response times .............................................. 9-21
Scheduled Interrupt Interval .................................. 9-16
Serial Port Settings ............................................... 9-23
Set Time to All Events ........................................... 9-30
Settings for FINS write protection via network ...... 9-31
Special I/O Unit cyclic refreshing .......................... 9-19
Startup Hold settings ............................................... 9-5
Startup operation settings ....................................... 9-5
time and interrupt settings ..................................... 9-14
Watch Cycle Time ................................................. 9-14
PLC setup ..................................................................... 2-3
Power Interruption Time .............................................. 10-5
power OFF detection delay setting ........................... 10-24
power OFF detection delay time ................................. 9-17
Power OFF Interrupt disabled ..................................... 9-18
power OFF interrupt task ................................... 5-22, 9-18
Power ON Clock Data ................................................. 10-4
processing at power interruptions ................................. 3-7
program capacity .......................................................... 5-5
program error ............................................................ 5-104
program execution ........................................................ 3-4
program index ............................................................... 2-3
program index file .......................................................... 7-9
PROGRAM mode ......................................................... 3-8
program operation protection using production lot numbers
10-55
program section
block program section ......................................... 5-110
FOR-NEXT loop .................................................. 5-110
IL - ILC section .................................................... 5-110
JMP0 - JME0 section .......................................... 5-110
step ladder section .............................................. 5-110
subroutine ............................................................ 5-110
program/network symbol file ......................................... 7-7
programming language ................................................. 5-4
protocol macros ........................................................ 11-20
Pulse I/O Area ...................................................... 6-2, 6-17
R
read protection using passwords .............................. 10-50
relay network table ...................................................... 4-12
replacing the entire program ..................................... 10-43
response performance of Serial PLC Links .............. 12-15
response time for input interrupts ............................. 12-14
Retry Counts ............................................................... 9-13
rotary switch .................................................................. 4-2
routing tables ................................................2-3, 4-5, 4-11
RUN mode .................................................................... 3-8
RUN output ............................................................... 10-26
S
safety precautions ....................................................... 1-21
Scheduled Interrupt Interval ........................................ 9-16
scheduled interrupt task .............................................. 5-24
sections ....................................................................... 5-40
security functions ...................................................... 10-50
read protection using passwords ......................... 10-50
write protection from FINS commands ................ 10-56
write-protection using the DIP switch .................. 10-50
self-maintaining bits .................................................... 6-21
Serial PLC Link ......................................................... 11-21
Serial PLC Link Area ............................................ 6-2, 6-18
serial port settings ....................................................... 9-23
set time to all events ................................................... 9-30
setting allocated DM area words for CPU Bus
Units ......................................................................... 4-15
setting allocated DM area words for Special I/O
Units ......................................................................... 4-15
setting CPU Bus Units and Special I/O Units .............. 8-20
settings for FINS write protection via network ............. 9-31
SFC language ............................................................... 5-9
simple backup file ....................................................... 7-14
simple backup operation ............................................. 7-11
simulating system errors ........................................... 10-78
Slot Start Address Settings ......................................... 8-12
Source and Comment Areas ......................................... 2-3
source code .................................................................. 2-3
Special I/O Unit Area ........................................... 6-2, 6-16
Special I/O Unit cyclic refreshing ................................ 9-19
Special I/O Units
I/O allocations ........................................................ 6-27
special program sections .......................................... 5-110
specifying arrays ......................................................... 5-57
ST language .................................................................. 5-8
Startup Hold settings .................................................... 9-5
startup initialization ....................................................... 3-2
Startup operation settings ............................................. 9-5
startup settings and maintenance ............................. 10-22
step ladder section .................................................... 5-110
storing the stop position at errors .............................. 10-76
To Next Page
Loading...
Need help?
General