SATO s84ex - Page 230

222
Parameter
Item
Description
a
Print method
00H: Thermal transfer
01H: Direct thermal
* Direct thermal only is available in the direct thermal model.
b
Not used
00H: fixed
c
Print speed
[S84-ex]
Head density
Range
(inches/sec)
8dots/mm
(203 dpi)
4 - 16
12dots/mm
(305 dpi)
4 - 14
24dots/mm
(609 dpi)
2 - 6
[S86-ex]
Head density
Range
(inches/sec)
8dots/mm
(203 dpi)
4 - 14
12dots/mm
(305 dpi)
4 - 12
00H: 2 (inches/sec) 50 (mm/sec)
01H: 3 (inches/sec) 75 (mm/sec)
02H: 3 (inches/sec) 75 (mm/sec)
03H: 4 (inches/sec) 100 (mm/sec)
04H: 4 (inches/sec) 100 (mm/sec)
05H: 5 (inches/sec) 125 (mm/sec)
06H: 5 (inches/sec) 125 (mm/sec)
07H: 6 (inches/sec) 150 (mm/sec)
08H: 6 (inches/sec) 150 (mm/sec)
09H: 7 (inches/sec) 175 (mm/sec)
0AH: 7 (inches/sec) 175 (mm/sec)
0BH: 8 (inches/sec) 200 (mm/sec)
0CH: 8 (inches/sec) 200 (mm/sec)
0DH: 9 (inches/sec) 225 (mm/sec)
0EH: 9 (inches/sec) 225 (mm/sec)
0FH: 10 (inches/sec) 250 (mm/sec)
10H: 10 (inches/sec) 250 (mm/sec)
11H: 11 (inches/sec) 275 (mm/sec)
12H: 11 (inches/sec) 275 (mm/sec)
13H: 12 (inches/sec) 325 (mm/sec)
14H: 12 (inches/sec) 325 (mm/sec)
15H: 13 (inches/sec) 350 (mm/sec)
16H: 13 (inches/sec) 350 (mm/sec)
17H: 14 (inches/sec) 375 (mm/sec)
18H: 14 (inches/sec) 375 (mm/sec)
19H: 15 (inches/sec) 400 (mm/sec)
1AH: 15 (inches/sec) 400 (mm/sec)
1BH: 16 (inches/sec) 425 (mm/sec)
1CH: 16 (inches/sec) 425 (mm/sec)
d
Print operation
00H: Continuous
03H: Dispense (Default)
04H: NONSEPA
e
Not used
00H: fixed
f
Dispensing motion
00H: Motion 1 (at head place)
01H: Motion 2 (at dispense place) (Default)
02H: No backfeed
g
Not used
00H: fixed
h
Print darkness
41H: A (fixed)
h
Print darkness level
01H: Darkness 1
02H: Darkness 2
03H : Darkness 3
04H : Darkness 4
05H: Darkness 5 (Default)
06H : Darkness 6
07H : Darkness 7
08H : Darkness 8
09H : Darkness 9
0AH : Darkness 10
i
Sensor type
00H: Reflective sensor
01H: Transmissive sensor (Default)
02H: Ignore sensor
j
Zero slash
00H: Disable
01H: Enable (Default)
k
Character code
02H: UTF-16
03H: UTF-8 (Default)