What causes a buffer overflow on a SATO Label Maker?
A buffer overflow on your SATO Label Maker happens either because the received data's size is too large for the receive buffer, or the communication settings between the printer and the host are incorrect. Avoid sending data exceeding the buffer size, and ensure the communication settings between the printer and the host are correctly configured.
What to do when SATO s84ex Label Maker displays a memory full error?
If your SATO Label Maker shows a 'Memory Full Error', it means that there is not enough space in the memory. To fix this, delete any unnecessary data from the memory.
What causes an overheat error on a SATO Label Maker?
An overheat error on your SATO Label Maker occurs when the printer's temperature exceeds its tolerance value. To resolve this, stop using the printer and allow it to cool down.
How to fix SD card write error on SATO s84ex?
If you're encountering an SD card write error on your SATO Label Maker, start by ensuring the SD card is properly connected. If it is, verify that it isn't write-protected; if it is, release the write-protect. If the issue continues, the SD card may need to be replaced.
Why does my SATO Label Maker say ribbon end?
The 'Ribbon End' error on your SATO Label Maker typically means that the ribbon is either not loaded, not loaded correctly or damaged. Try loading a new ribbon or ensuring that the existing ribbon is correctly loaded. If the ribbon is torn, clean and adjust the ribbon path.
What to do if the SATO Label Maker shows a paper end error?
If your SATO Label Maker displays a paper end error, it could be due to several reasons. First, ensure that the media is loaded correctly. Check also that the media sensor is clean and that its cable is properly connected. Adjust the sensor level if the sensitivity is not set correctly. If the media is jammed, remove it.
What to do if my SATO s84ex Label Maker displays a 'Parity error'?
If your SATO Label Maker displays a 'Parity error', 'Overrun error', or 'Framing error', it is likely due to incorrect RS-232C settings or an incorrect cable connection. Adjust the interface settings correctly and ensure the cable is properly connected.
What to do if my SATO Label Maker displays a 'Sensor cover open error'?
If your SATO Label Maker displays a 'Sensor cover open error', it means the sensor cover is unlocked or the sensor for sensing the open/close status of the sensor cover is defective. Ensure the sensor cover is locked. If the error persists, the sensor may need to be replaced.
What to do if my SATO s84ex Label Maker displays a 'Print head error'?
If your SATO Label Maker displays a 'Print head error', it could be because the print elements are worn out or the print head is damaged. If the print elements are worn out, change print head check conditions to only check for missing elements in barcodes and try to adjust missing elements to white bars. If the print head is damaged, it needs to be replaced.
What to do if my SATO Label Maker displays a 'Sensor error'?
If your SATO Label Maker displays a 'Sensor error', it could be due to an incorrect media sensor level, an incorrect sensor type, or meandering media. Adjust the media sensor level and ensure you are using the correct sensor type. If the media is meandering, clean and adjust the media path.
General| Max Print Length | 39.37 inches |
|---|---|
| Print Method | Thermal Transfer / Direct Thermal |
| Connectivity | USB, Serial |
| Supported Barcode Types | Data Matrix, PDF417, QR Code |
| Supported Media Types | Roll, Fanfold |
| Media Thickness | 0.002 to 0.008 inches |
| Operating Temperature | 41 to 95°F (5 to 35°C) |
| Dimensions | 18.11" D x 12.6" H |
| Print Width | 4.09 inches |
| Max Print Width | 4.09 inches |
| Memory | 16MB Flash, 32MB SDRAM |
To Next Page
