Siemens SINAMICS G130 - Page 598

Appendix
A.2 Parameter macros
Inverter chassis units
598 Operating Instructions, 07/2016, A5E00331449A
Parameter macro p0700 = 4: PROFIdrive+TM31 (70004)
This macro is used to set the PROFIdrive interface and terminal block TM31 as the
command source.
Table A- 5 Parameter macro p0700 = 4: PROFIdrive+TM31
Sink
Source
Parameter
Description
DO
Parameter
Description
DO
p0840[0]
ON/OFF1
Vector
r2090.0
PZD 1 bit 0
Vector
p0844[0]
No OFF2_1
Vector
r2090.1
PZD 1 bit 1
Vector
p0845[0] No OFF2_2 Vector r4022.4 TM31 DI4 TM31
p0848[0]
No OFF3_1
Vector
r2090.2
PZD 1 bit 2
Vector
p0849[0] No OFF3_2 Vector r4022.5 TM31 DI5 TM31
p0806
Inhibit LOCAL mode
Vector
0
Vector
p0810
Changeover CDS bit 0
Vector
0
Vector
p0852
Enable operation
Vector
r2090.3
PZD 1 bit 3
Vector
p0854
Control request
Vector
r2090.10
PZD 1 bit 10
Vector
p0922
Profibus PZD telegram selection
Vector
999
Free telegram configuration
p1020
FSW bit 0
Vector
0
Vector
p1021
FSW bit 1
Vector
0
Vector
p1035
MOP raise
Vector
r2090.13
PZD 1 bit 13
Vector
p1036
MOP lower
Vector
r2090.14
PZD 1 bit 14
Vector
p1113
Direction of rotation reversal
Vector
r2090.11
PZD 1 bit 11
Vector
p1140
Enable RFG
Vector
r2090.4
PZD 1 bit 4
Vector
p1141
Start RFG
Vector
r2090.5
PZD 1 bit 5
Vector
p1142
Enable nsetp
Vector
r2090.6
PZD 1 bit 6
Vector
p2103
Acknowledge fault 1
Vector
r2090.7
PZD 1 bit 7
Vector
p2104
Acknowledge fault 2
Vector
r4022.3
TM31 DI3
TM31
p2106
Ext. fault_1
Vector
r4022.6
TM31 DI6
TM31
p2107 Ext. fault_2 Vector 1 Vector
p2112
Ext. alarm_1
Vector
r4022.11
TM31 DI11
TM31
p2116
Ext. alarm_2
Vector
1
Vector
p0738
DI/DO8
CU
0
CU
p0748.8
Invert DI/DO8
CU
0
Not inverted
p0728.8
Set DI/DO8 input or output
CU
1
Output
p0739 DI/DO9 CU 0 CU
p0748.9
Invert DI/DO9
CU
0
Not inverted
p0728.9
Set DI/DO9 input or output
CU
1
Output
p0740
DI/DO10
CU
0
CU
p0748.10
Invert DI/DO10
CU
0
Not inverted
p0728.10
Set DI/DO10 input or output
CU
1
Output
p0741
DI/DO11
CU
0
CU
p0748.11
Invert DI/DO11
CU
0
Not inverted
p0728.11
Set DI/DO11 input or output
CU
1
Output