Siemens SINUMERIK 802D sl Function Manual

Various Interface Signals (A2)
1.2 Signals from PLC to NCK
Turning, Milling, Nibbling
Function Manual, 11/2012, 6FC5397-1CP10-5BA0
21
'HFUHDVLQJ
DFFHVVDXWKRUL]DWLRQ
$FFHVVWRH[DPSOHV8VHU7\SH3URWHFWLRQ
OHYHO

3DVV
ZRUG
6,(0(16UHVHUYHG

3DVV
ZRUG
([SHUWPRGH
'HILQHGIXQFWLRQVSURJUDPVDQGGDWD

3DVV
ZRUG
0DFKLQHPDQXIDFWXUHU
'HILQHGIXQFWLRQVSURJUDPVDQGGDWD
IRUVWDQGDUGFRPPLVVLRQLQJ

3DVV
ZRUG
(QGXVHU $VVLJQHGIXQFWLRQVSURJUDPVDQGGDWD

,6
9

(QGXVHU
SURJUDPPHU
VHWXSHQJLQHHU
/HVVWKDQSURWHFWLRQOHYHOWR
VSHFLILHGE\PDFKLQHPDQXIDFWXUHURU
HQGXVHU

,6
9

(QGXVHU
TXDOLILHGRSHUDWRU
ZKRGRHVQRWSURJUDP
/HVVWKDQSURWHFWLRQOHYHOWR
VSHFLILHGE\HQGXVHU

,6
9

(QGXVHU
WUDLQHGRSHUDWRU
ZKRGRHVQRWSURJUDP
RQO\SURJUDPVHOHFWLRQWRROZHDULQSXW
DQGLQSXWRI]HURRIIVHWV

,6
9

(QGXVHU
VHPLVNLOOHGRSHUDWRU
1RLQSXWVDQGSURJUDPVHOHFWLRQSRVVLEOH
RQO\RSHUDWLRQRIPDFKLQHFRQWUROSDQHO
Figure 1-2 Access protection
1.2.2 General signals
Delete distance-to-go (V3200 0006.2)
IS "Delete distancetogo (channelspecific)" is only active for path axes.
With the rising edge of the interface signal, the distancestogo of all axes in the geometry
grouping are deleted and thus brought to a standstill with ramp stop. The next program block
is then started.
Axis/spindle disable (V380x 0001.3)
IS "Axis/spindle disable" can be used for test purposes.
Axis disable (for axis):
If IS "Axis disable" is output - for this axis - no more position partial setpoints are output to
the position controller; the axis travel is therefore disabled. The position control loop remains
closed and the remaining following error is reduced to zero. If an axis is moved with axis
disable the actual value position display shows the setpoint position and the actual velocity
value display shows the setpoint velocity even though the machine axis is not actually
moving. IS "RESET" (V3000 0000.7) sets the position actual value display to the real actual
value of the machine. Travel commands continue to be output to the PLC for this axis. If the
interface signal is cancelled again the associated axis can again traverse normally. If the
interface signal "Axis disable" is set for a traversing axis, the axis is stopped with a ramp
stop.

Siemens SINUMERIK 802D sl Specifications

General

Brand	Siemens
Model	SINUMERIK 802D sl
Category	Controller
Language	English