Simplex 4100U - Introduction; Chapter 9 PC Software Connections; In this Chapter

To Next Page

To Previous Page

9-1

The service port on the door with the Operator Interface enables the 4100U to connect to

PCs running important utilities, such as diagnostics, programming, CPU firmware

downloading, and channel monitoring.

Refer to the page number listed in this table for information on a specific topic.

Topic See Page #

Software Modes

9-2

Chapter 9

PC Software Connections

Introduction

In this Chapter

Main Page

Default Chapter3
- Approvals3
- Copyrights and Trademarks3
- Manufacture3
- Product / Site3
- End User Liability Disclaimer4
- Non-Disclosure Agreement4
- Amendment Log5
- Document5
- Model Number & Firmware Revision5
- Cautions, Warnings, and Regulatory Information6
- Table of Contents7
- List of Figures16
Chapter 1 Introduction to the 4100U Fire Alarm System19
- Introduction19
- In this Chapter19
- Topic See Page19
- System Configurations20
  - Overview20
- Standalone Configuration21
- Figure 1-1. Standalone 4100U System21
- MINIPLEX Configuration22
- Network Configuration24
- 4100 Pids (Non-4100U)26
  - Annunciation Modules26
- 4100U Cabinet Part Identification Numbers (Pids)27
  - Overview27
  - 4100U Cabinets27
- 4100U Pids27
Chapter 2 Installing 4100U FACP Components29
- Introduction29
- In this Chapter29
- Introduction to Facps (4100U)30
- Step 1. Mounting Cabinets (4100U)37
  - Overview37
- Step 2. Mounting Card Bays to Cabinets (4100U)37
- Figure 2-6. Bracket Mounting37
- Step 3. Configuring Cards (4100U)38
- Step 4. Interconnecting Modules and Bays39
- Step 5. Installing Modules into Expansion Bays (4100U)43
- Step 6. Installing Led/Switch Modules into Expansion Bays (4100U)48
- The Terminal Block Utility Module (4100U)55
Chapter 3 Installing 4100 MINIPLEX Components (Non-4100U)57
- Introduction57
- In this Chapter57
- Introduction to MINIPLEX Systems (Non-4100U)58
  - Overview58
  - Figure 3-1. MINIPLEX System Design59
- MINIPLEX System Components (Non-4100U)60
- MINIPLEX System Guidelines (Non-4100U)62
  - Overview62
  - Guidelines62
- Installing Modules into Cabinets (Non-4100U)63
- MINIPLEX Wiring (Non-4100U)67
Chapter 4 Installing 4100U MINIPLEX Components69
- Introduction69
- In this Chapter69
- Introduction to MINIPLEX Transponders (4100U)70
- MINIPLEX System Guidelines (4100U)75
  - Overview75
  - Guidelines75
- Configuring Cards (4100U)76
- Tic/Riser Mounting (4100U)77
- Tic/Motherboard Interconnections (4100U)78
- Figure 4-3. Transponder Cabinet Interconnections78
- RUI Wiring (4100U)79
Chapter 5 Networking81
- Introduction81
- In this Chapter81
- Getting Started82
  - Overview82
  - Overview83
- Introduction to the 4100 Network Interface Card (NIC)83
- Step 1. Configuring Network Cards87
- Step 2. Mounting Media Cards to the NIC89
- Step 3. Mounting Network Cards90
- Figure 5-7. Installing the Daughter Card90
- Step 4. Wiring Network Cards91
Chapter 6 The System Power Supply & Alarm Relay Card101
- Introduction101
- In this Chapter101
- SPS Specifications102
- SPS Configuration104
- SPS LED Indications105
  - Leds105
- Troubleshooting on SPS106
- The Alarm Relay Card107
Chapter 7 SPS Field Wiring (4100U)109
- Introduction109
- In this Chapter109
- General Field Wiring Guidelines110
  - General Guidelines110
  - Figure 7-1. the Ferrite Bead (SX0005)110
- SPS NAC Field Wiring Guidelines111
- Power Supply Wiring Distances113
- SPS Auxiliary Power Wiring116
- SPS Relay Wiring118
- SPS Idnet Wiring120
Chapter 8 Installing 4100U Idnet & 4100MXP Cards123
- Introduction123
- In this Chapter123
- The Idnet Card124
- Installing the Idnet Card Onto the PDI126
- Overview126
  - Figure 8-2. Mounting Onto the Power Distribution Interface126
  - Overview127
- Installing the ID-Net into a 4100 Card Bay127
- Figure 8-3. Mounting into 4100 (Legacy) Bay127
- Configuring the Card128
- Wiring to Idnet Devices129
- Troubleshooting on Idnet132
- The 4100MXP133
  - Introduction135
Chapter 9 PC Software Connections135
- In this Chapter135
- Software Modes136
Chapter 10 Australian Version Specifics139
- In this Chapter139
- Introduction139
- Summary of Australian Version Specifics140
  - Overview140
  - AS4428 Requirements140
- Australian Panel Format141
- 4100U Fan Control Module142
- Brigade Interfaces144
Chapter 11 Installation Checklist, Commissioning & Maintenance145
- Introduction145
- In this Chapter145
- Installation Checklist146
  - Overview146
  - Overview147
- Alignment & Adjustment147
- Power up & Placing into Operation148
- Maintenance149
Appendix A the Device Configuration DIP Switch151
- Overview151
- Table A-1 Card Addresses152
Appendix B Programming Requirements153
- In this Chapter153
- Introduction153
- Required Features153
- Notes153
Appendix C Checking System Wiring154
- Overview154
- Using the Volt/ Ohm Meter154
- Figure D-1. Volt/Ohm Meter Readings154
- Meter Readings155
- Table C-1 Acceptable Zone and Signal Circuit Meter Readings155
Appendix D Earth Fault Detection156
- Overview156
- General Guidelines157
- Earth Fault Searching from the Front Panel158
- Search Results161
- Earth Fault Search Example163
Appendix E Related Documentation165
Appendix F Compatible Actuating Devices168
- Introduction168
- In this Chapter168
- List of Approved Devices168
- Compatible Detectors, IDNET171
- Compatible Addressable Field Devices, Idnet172
Appendix G Compatible Batteries173
Appendix H 4100U Specifications174
- General174
- Fuses174
- Firmware Features174
- Voltage & Current Ratings of Modules & Assemblies175
Appendix I Power Supply & Battery Capacity Calculations176
- Power Supply176
- Battery Capacity176
Appendix J Cable Characteristics177
- Idnet177
- 4100 Mapnet II177
- Network177
Appendix K List of Drawings179

Simplex 4100U - Introduction; Chapter 9 PC Software Connections; In this Chapter

Table of Contents

Other manuals for Simplex 4100U

Related product manuals