Simplex 4100U - Amendment Log; Document; Model Number & Firmware Revision

To Next Page

To Previous Page

iii

This manual applies to product with the following:

Model number : 4100U

Firmware revision : 11.08 and on

Document Name : LT0350 4100U Installation & Maintenance Manual

Cross Reference : 574-848 4100U Installation Manual (USA)

Issue : 1.0-G 14 May, 2004

14 May, 2004 Issue 1.0.6 Original based on 574-848 Rev G

Model Number & Firmware Revision

Document

Amendment Log

Main Page

Default Chapter3
- Approvals3
- Copyrights and Trademarks3
- Manufacture3
- Product / Site3
- End User Liability Disclaimer4
- Non-Disclosure Agreement4
- Amendment Log5
- Document5
- Model Number & Firmware Revision5
- Cautions, Warnings, and Regulatory Information6
- Table of Contents7
- List of Figures16
Chapter 1 Introduction to the 4100U Fire Alarm System19
- Introduction19
- In this Chapter19
- Topic See Page19
- System Configurations20
  - Overview20
- Standalone Configuration21
- Figure 1-1. Standalone 4100U System21
- MINIPLEX Configuration22
- Network Configuration24
- 4100 Pids (Non-4100U)26
  - Annunciation Modules26
- 4100U Cabinet Part Identification Numbers (Pids)27
  - Overview27
  - 4100U Cabinets27
- 4100U Pids27
Chapter 2 Installing 4100U FACP Components29
- Introduction29
- In this Chapter29
- Introduction to Facps (4100U)30
- Step 1. Mounting Cabinets (4100U)37
  - Overview37
- Step 2. Mounting Card Bays to Cabinets (4100U)37
- Figure 2-6. Bracket Mounting37
- Step 3. Configuring Cards (4100U)38
- Step 4. Interconnecting Modules and Bays39
- Step 5. Installing Modules into Expansion Bays (4100U)43
- Step 6. Installing Led/Switch Modules into Expansion Bays (4100U)48
- The Terminal Block Utility Module (4100U)55
Chapter 3 Installing 4100 MINIPLEX Components (Non-4100U)57
- Introduction57
- In this Chapter57
- Introduction to MINIPLEX Systems (Non-4100U)58
  - Overview58
  - Figure 3-1. MINIPLEX System Design59
- MINIPLEX System Components (Non-4100U)60
- MINIPLEX System Guidelines (Non-4100U)62
  - Overview62
  - Guidelines62
- Installing Modules into Cabinets (Non-4100U)63
- MINIPLEX Wiring (Non-4100U)67
Chapter 4 Installing 4100U MINIPLEX Components69
- Introduction69
- In this Chapter69
- Introduction to MINIPLEX Transponders (4100U)70
- MINIPLEX System Guidelines (4100U)75
  - Overview75
  - Guidelines75
- Configuring Cards (4100U)76
- Tic/Riser Mounting (4100U)77
- Tic/Motherboard Interconnections (4100U)78
- Figure 4-3. Transponder Cabinet Interconnections78
- RUI Wiring (4100U)79
Chapter 5 Networking81
- Introduction81
- In this Chapter81
- Getting Started82
  - Overview82
  - Overview83
- Introduction to the 4100 Network Interface Card (NIC)83
- Step 1. Configuring Network Cards87
- Step 2. Mounting Media Cards to the NIC89
- Step 3. Mounting Network Cards90
- Figure 5-7. Installing the Daughter Card90
- Step 4. Wiring Network Cards91
Chapter 6 The System Power Supply & Alarm Relay Card101
- Introduction101
- In this Chapter101
- SPS Specifications102
- SPS Configuration104
- SPS LED Indications105
  - Leds105
- Troubleshooting on SPS106
- The Alarm Relay Card107
Chapter 7 SPS Field Wiring (4100U)109
- Introduction109
- In this Chapter109
- General Field Wiring Guidelines110
  - General Guidelines110
  - Figure 7-1. the Ferrite Bead (SX0005)110
- SPS NAC Field Wiring Guidelines111
- Power Supply Wiring Distances113
- SPS Auxiliary Power Wiring116
- SPS Relay Wiring118
- SPS Idnet Wiring120
Chapter 8 Installing 4100U Idnet & 4100MXP Cards123
- Introduction123
- In this Chapter123
- The Idnet Card124
- Installing the Idnet Card Onto the PDI126
- Overview126
  - Figure 8-2. Mounting Onto the Power Distribution Interface126
  - Overview127
- Installing the ID-Net into a 4100 Card Bay127
- Figure 8-3. Mounting into 4100 (Legacy) Bay127
- Configuring the Card128
- Wiring to Idnet Devices129
- Troubleshooting on Idnet132
- The 4100MXP133
  - Introduction135
Chapter 9 PC Software Connections135
- In this Chapter135
- Software Modes136
Chapter 10 Australian Version Specifics139
- In this Chapter139
- Introduction139
- Summary of Australian Version Specifics140
  - Overview140
  - AS4428 Requirements140
- Australian Panel Format141
- 4100U Fan Control Module142
- Brigade Interfaces144
Chapter 11 Installation Checklist, Commissioning & Maintenance145
- Introduction145
- In this Chapter145
- Installation Checklist146
  - Overview146
  - Overview147
- Alignment & Adjustment147
- Power up & Placing into Operation148
- Maintenance149
Appendix A the Device Configuration DIP Switch151
- Overview151
- Table A-1 Card Addresses152
Appendix B Programming Requirements153
- In this Chapter153
- Introduction153
- Required Features153
- Notes153
Appendix C Checking System Wiring154
- Overview154
- Using the Volt/ Ohm Meter154
- Figure D-1. Volt/Ohm Meter Readings154
- Meter Readings155
- Table C-1 Acceptable Zone and Signal Circuit Meter Readings155
Appendix D Earth Fault Detection156
- Overview156
- General Guidelines157
- Earth Fault Searching from the Front Panel158
- Search Results161
- Earth Fault Search Example163
Appendix E Related Documentation165
Appendix F Compatible Actuating Devices168
- Introduction168
- In this Chapter168
- List of Approved Devices168
- Compatible Detectors, IDNET171
- Compatible Addressable Field Devices, Idnet172
Appendix G Compatible Batteries173
Appendix H 4100U Specifications174
- General174
- Fuses174
- Firmware Features174
- Voltage & Current Ratings of Modules & Assemblies175
Appendix I Power Supply & Battery Capacity Calculations176
- Power Supply176
- Battery Capacity176
Appendix J Cable Characteristics177
- Idnet177
- 4100 Mapnet II177
- Network177
Appendix K List of Drawings179

Simplex 4100U - Amendment Log; Document; Model Number & Firmware Revision

Table of Contents

Other manuals for Simplex 4100U

Related product manuals