Agilent Technologies InfiniiVision 5000 Series User Manual

Initial Setup 2
InfiniiVision Oscilloscopes User’s Guide 35
W2637A LPDDR BGA probe, x16, 404 MHz, 100 ohm input impedance
W2638A LPDDR BGA probe, x32, 404 MHz , 100 ohm input impedance
W2639A Oscilloscope Adapter Board, 1.5 GHz, 75 ohm input impedance
N5450A InfiniiMax Extreme Temperature Extension Cables, to be used with InfiniiMax
probe amplifiers and heads, 92 cm (36 in)
N2791A Differential probe, 1 MOhm termination, 10:1 or 100:1 (switchable), 25 MHz
N2792A Differential probe, 50 Ohm termination, 10:1, 200 MHz, compatible with all
InfiniiVision models except 6000 Series 100 MHz models (MSO/DSO601x)
N2793A Differential probe, 50 Ohm termination, 10:1, 800 MHz, compatible with all
InfiniiVision models except 6000 Series 100 MHz models (MSO/DSO601x)
1156A Active Probe, 1.5 GHz
1144A Active Probe, 800 MHz (requires 1142A – power supply)
1145A
†
Active Probe, 750 MHz 2-ch (requires 1142A – power supply)
1130A
†
For active differential probes: 1.5 GHz InfiniiMax amplifier (requires one or more
InfiniiMax probe head – E2675A, E2668A, E2669A).
N2772A Active Differential Probe, 20 MHz, 1.2 kVDC + peak AC max (requires N2773A
power supply)
1141A Active Differential Probe, 200 MHz, 200 VDC + peak AC max (requires 1142A
power supply)
1146A Current Probe, 100 kHz, 100 A, AC/DC
1147A
†
Current Probe, 50 MHz, 30 A, AC/DC with AutoProbe interface
N2780A Current Probe, 2 MHz, 500 A, AC/DC (use with N2779A power supply)
N2781A Current Probe, 10 MHz, 150 A, AC/DC (use with N2779A power supply)
N2782A Current Probe, 50 MHz, 30 A, AC/DC (use with N2779A power supply)
N2783A Current Probe, 100 MHz, 30 A, AC/DC (use with N2779A power supply)
10072A Fine-Pitch Probe Kit
10075A 0.5 mm IC Clip Kit
10076A 100:1, 4 kV 250 MHz Probe
E2613B 0.5 mm Wedge Probe Adapter, 3-signal, qty 2
E2614A 0.5 mm Wedge Probe Adapter, 8-signal, qty 1
E2615B 0.65 mm Wedge Probe Adapter, 3-signal, qty 2
E2616A 0.65 mm Wedge Probe Adapter, 8-signal, qty 1
E2643A 0.5 mm Wedge Probe Adapter, 16-signal, qty 1
E2644A 0.65 mm Wedge Probe Adapter, 16-signal, qty 1
†
Indicates a maximum of two of this model probe can be connected to each oscilloscope due to
AutoProbe interface current supply limitation. See also
“Passive Probes” on page 73 and
“Active Probes” on page 74.
Model Description

Agilent Technologies InfiniiVision 5000 Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 5000 Series
Category	Test Equipment
Language	English