Allied Telesis AT-SBx908 Gen2 - Page 7

7
Figure 1: Front Panel of the AT-SBx908 Gen2 Chassis.......................................................................................................21
Figure 2: Rear Panel of the AT-SBx908 Gen2 Chassis........................................................................................................21
Figure 3: AT-SBx908 Gen2 Ethernet Line Cards .................................................................................................................22
Figure 4: Management Panel ...............................................................................................................................................27
Figure 5: Switch ID LED .......................................................................................................................................................30
Figure 6: AT-SBxPWRSYS2 and AT-SBxPWRSYS1-80 Power Supplies ...........................................................................32
Figure 7: AT-FAN08 Module.................................................................................................................................................34
Figure 8: PORT Parameter in the Command Line Interface.................................................................................................35
Figure 9: NEMA 5-20P Plug and Receptacle .......................................................................................................................43
Figure 10: AT-SBx908 Gen2 Switch Shipping Box...............................................................................................................44
Figure 11: Lifting the Switch from the Shipping Box.............................................................................................................45
Figure 12: Removing the Switch from the Protective Shipping Bag. ....................................................................................45
Figure 13: Pre-installed Items on the Front and Side Panels ...............................................................................................46
Figure 14: Pre-installed Items on the Rear Panel.................................................................................................................47
Figure 15: Accessory Kit.......................................................................................................................................................48
Figure 16: Items in the Shipping Box for the AT-SBxPWRSYS2 AC Power Supply ............................................................49
Figure 17: Items in the Shipping Box for the AT-SBxPWRSYS1-80 DC Power Supply.......................................................50
Figure 18: Chassis Orientations in the Equipment Rack ......................................................................................................53
Figure 19: Chassis Orientations in the Equipment Rack (Continued) ..................................................................................54
Figure 20: Chassis Orientations in the Equipment Rack (Continued) ..................................................................................55
Figure 21: Example of Adjusting the Equipment Rack Brackets ..........................................................................................56
Figure 22: Securing the Chassis to the Equipment Rack .....................................................................................................57
Figure 23: Stripping the Grounding Wire..............................................................................................................................58
Figure 24: Removing the Grounding Lug from the Chassis..................................................................................................59
Figure 25: Attaching the Grounding Wire to the Grounding Lug...........................................................................................59
Figure 26: Installing the Grounding Lug and Wire ................................................................................................................60
Figure 27: Removing the Blank Power Supply Panel from Power Supply Slot B.................................................................62
Figure 28: Lifting the Locking Handle on the AT-SBxPWRSYS2 Power Supply..................................................................62
Figure 29: Sliding the AT-SBxPWRSYS2 AC Power Supply into the Chassis.....................................................................63
Figure 30: Lowering the Locking Handle on the AT-SBxPWRSYS2 AC Power Supply.......................................................64
Figure 31: On/Off Switch on the AT-SBxPWRSYS1-80 DC Power Supply..........................................................................66
Figure 32: Loosening the Handle locking Screw on the AT-SBxPWRSYS1-80 DC Power Supply......................................66
Figure 33: Lifting the Locking Handle on the AT-SBxPWRSYS1-80 DC Power Supply.......................................................67
Figure 34: Inserting the AT-SBxPWRSYS1-80 DC Power Supply.......................................................................................67
Figure 35: Lowering the Locking Handle on the AT-SBxPWRSYS1-80 DC Power Supply..................................................68
Figure 36: Removing a Blank Line Card Cover ....................................................................................................................69
Figure 37: Removing the Ethernet Line Card from the Anti-static Bag.................................................................................70
Figure 38: Sliding the Ethernet Line Card into the Slot.........................................................................................................71
Figure 39: Seating an Ethernet Line Card in the Chassis.....................................................................................................72
Figure 40: Tightening the Two Captive Screws on the Ethernet Line Card..........................................................................72
Figure 41: Installing a Blank Slot Cover................................................................................................................................73
Figure 42: Tightening the Captive Screws on a Blank Slot Cover........................................................................................74
Figure 43: Lifting the Locking Handle on the Blank Power Supply Slot Cover.....................................................................75
Figure 44: Aligning the Blank Power Supply Cover in the Slot...................................................................
..........................76
Figure 45: Lowering the Locking Handle on the Blank Power Supply Slot Cover ................................................................76
Figure 46: Installing the Power Cord Retaining Clips ...........................................................................................................77
Figure 47: Connecting the AC Power Cord ..........................................................................................................................82
Figure 48: Securing the Power Cord with the Retaining Clip................................................................................................82
Figure 49: Connecting the Power Cord to an AC Power Source..........................................................................................83
Figures