Allied Telesis AT-SBx908 Gen2 - Page 8

Figures
8
Figure 50: Components on the AT-SBxPWRSYS1-80 DC Power Supply............................................................................85
Figure 51: Grounding Wire Terminal.....................................................................................................................................86
Figure 52: Stripping the Stranded Grounding Wire...............................................................................................................86
Figure 53: Attaching the Stranded Grounding Wire to the Grounding Terminal ...................................................................86
Figure 54: On/Off Switch on the AT-SBxPWRSYS1-80 DC Power Supply..........................................................................87
Figure 55: Removing the Nut and Washer from the Grounding Post ...................................................................................88
Figure 56: Attaching the Grounding Lug and Wire to the Grounding Post............................................................................89
Figure 57: Securing the Grounding Wire ..............................................................................................................................90
Figure 58: Stripping the solid or Stranded Grounding Wire ..................................................................................................91
Figure 59: Attaching the Bare Grounding Wire to the Grounding Post.................................................................................91
Figure 60: Securing the Bare Grounding Wire to the Grounding Post..................................................................................92
Figure 61: Power Wire Terminals .........................................................................................................................................93
Figure 62: Stripping the Power Wires...................................................................................................................................94
Figure 63: Attaching the Power Wires to the Straight Terminal Lugs ...................................................................................94
Figure 64: Opening the Plastic Cover...................................................................................................................................95
Figure 65: Removing the Terminal Screws...........................................................................................................................96
Figure 66: Connecting the Positive (+) Power Wire with a Straight Terminal.......................................................................97
Figure 67: Connecting the Negative (-) Power Wire with a Straight Terminal ......................................................................98
Figure 68: Closing the Plastic Cover over the Terminal Connectors ....................................................................................99
Figure 69: Tightening the Handle Locking Screw...............................................................................................................100
Figure 70: Stripping the Power Wires.................................................................................................................................101
Figure 71: Attaching the Power Wires to the Right Angle Terminal Lugs...........................................................................101
Figure 72: Removing the Plastic Cover ..............................................................................................................................102
Figure 73: Removing the Terminal Screws........................................................................................
.................................103
Figure 74: Connecting the Positive (+) Power Wire with a Right Angle Terminal...............................................................104
Figure 75: Connecting the Negative (-) Power Wire with a Right Angle Terminal ..............................................................105
Figure 76: Tightening the Handle Locking Screw...............................................................................................................106
Figure 77: Stripping Solid or Stranded DC Power Wires....................................................................................................107
Figure 78: Connecting the Positive Wire With Bare Wire ...................................................................................................108
Figure 79: Connecting the Negative Lead Wire with Bare Wire..........................................................................................109
Figure 80: Switch Initialization Messages...........................................................................................................................111
Figure 81: Switch Initialization Messages (Continued) .......................................................................................................112
Figure 82: Switch Initialization Messages (Continued) .......................................................................................................113
Figure 83: Connecting the Management Cable to the Console RS-232 Port .....................................................................114
Figure 84: SHOW CARD Command...................................................................................................................................116
Figure 85: Installing an SFP Transceiver............................................................................................................................120
Figure 86: Removing the Dust Cover from an SFP or SFP+ Transceiver ..........................................................................121
Figure 87: Positioning the SFP or SFP+ Handle in the Upright Position ............................................................................121
Figure 88: Connecting a Fiber Optic Cable to an SFP or SFP+ Transceiver .....................................................................122
Figure 89: Installing AT-SP10TW Cables in the AT-XEM2-12XS Line Card ......................................................................123
Figure 90: Removing the Dust Cover from a Slot on the AT-XEM2-4QS Line Card...........................................................126
Figure 91: Sliding the AT-QSFPCU Cable into the Slot......................................................................................................127
Figure 92: Disconnecting the AC Power Cord from the Power Source ..............................................................................131
Figure 93: Disconnecting the AC Power Cord from the Chassis ........................................................................................131
Figure 94: Lifting the Locking Handle on the AT-SBxPWRSYS2 AC Power Supply ..........................................................132
Figure 95: Removing the AT-SBxPWRSYS2 AC Power Supply ........................................................................................133
Figure 96: Loosening the Screw on the Locking Handle ....................................................................................................134
Figure 97: Opening the Plastic Window over the Terminal Block.......................................................................................135
Figure 98: Removing the Negative Lead Wire....................................................................................................................136
Figure 99: Removing the Positive Lead Wire from the Terminal Block...............................................................................137
Figure 100: Reinstalling the Screws on the Positive and Negative Terminals....................................................................138
Figure 101: Closing the Plastic Cover.................................................................................................................................139
Figure 102: Removing the Grounding Wire ........................................................................................................................140
Figure 103: Reinstalling the Nut and Washer on the Grounding Post ................................................................................141
Figure 104: Lifting the Locking Handle and Removing the Power Supply..........................................................................142
Figure 105: Installing the Blank Power Supply Slot Cover..................................................................................................143
Figure 106: Lowering the Locking Handle on the Power Supply Slot Cover ......................................................................144
Figure 107: Loosening the Screws on the Ethernet Line Card...........................................................................................146
Figure 108: Disconnecting an Ethernet Line Card from the Chassis..................................................................................147
Figure 109: Sliding an Ethernet Line Card from the Chassis..............................................................................................148