Anritsu MT8820C - Page 226

226
[Procedure using remote commands]
1. Execute PRESET to set default parameter.
2. Execute CALLPROC ON to set Common Parameter – Call Processing to On.
3. Execute CHCODING PACKET_DL_CA_PCC to set Common Parameter – Signal – Channel Coding to
Packet (DL CA).
4. Execute ANTCONFIG OPEN_LOOP to set Common Parameter – Signal – Antenna Configuration to
2x2MIMO (Open Loop).
5. Execute UECAT CAT9 set Common Parameter – Signal – UE Category to 9.
(When 4DL CA, Execute UECAT CAT11 set Common Parameter – Signal – UE Category to 11.)
6. Execute DLSCC 2 to set Call Processing Parameter – Carrier Aggregation – Number of DL SCC to 2.
(When 4DL CA, Execute DLSCC 3 to set Call Processing Parameter – Carrier Aggregation – Number of
DL SCC to 3.)
7. Execute BANDWIDTH 20MHZ to set Common Parameter – Frequency – Channel Bandwidth to 20 MHz.
8. Execute DLCHAN 300 to set Common Parameter - Frequency – UL Channel and DL Channel to 18300
and 300, respectively.
9. Execute OLVL_EPRE -70.0 to set Common Parameter – Level – Output Level(EPRE) to –70.0 dBm/15
kHz.
10. Execute ULRMC_RB 100 to set Common Parameter – UL RMC – Number of RB to 100.
11. Execute ULIMCS 23 to set Common Parameter – UL RMC – MCS Index to 23.
12. Execute DLRB 100,0 to set Common Parameter – DL RMC – Number of RB to 100, and Common
Parameter – DL RMC – Starting RB to 0.
13. Execute BANDWIDTH_SCC1 20MHZ to set Common Parameter – SCC1 – Channel Bandwidth to 20 MHz.
14. Execute DLIMCS1 28, DLIMCS2 28 and DLIMCS3 28 to set All of Common Parameter – DL RMC – MCS
Index1/2/3 to 28.
15. Execute DLCHAN_SCC1 498 to set Common Parameter – SCC1 – DL Channel to 498.
16. Execute OLVL_EPRE_SCC1 -70.0 to set Common Parameter – SCC-1 – Output Level(EPRE) to –70.0 dBm/15
kHz.
17. Execute DLRB_SCC1 100,0 to set Common Parameter – SCC1 – DL RMC - Number of RB to 100, and
Common Parameter – SCC1 – DL RMC – Starting RB to 0.
18. Execute DLIMCS1_SCC1 28, DLIMCS2_SCC1 28 and DLIMCS3_SCC1 28 to set All of Common Parameter –
SCC1 – DL RMC – MCS Index1/2/3 to 28.
19. Execute BANDWIDTH_SCC2 20MHZ to set Common Parameter – SCC2 – Channel Bandwidth to 20 MHz.
20. Execute DLCHAN_SCC2 1575 to set Common Parameter – SCC2 – DL Channel to 1575.
21. Execute OLVL_EPRE_SCC2 -70.0 to set Common Parameter – SCC-2 – Output Level(EPRE) to –70.0 dBm/15
kHz.
22. Execute DLRB_SCC2 100,0 to set Common Parameter – SCC2 – DL RMC - Number of RB to 100, and
Common Parameter – SCC2 – DL RMC – Starting RB to 0.
23. Execute DLIMCS1_SCC2 28, DLIMCS2_SCC2 28 and DLIMCS3_SCC2 28 to set All of Common Parameter -
SCC2 – DL RMC – MCS Index1/2/3 to 28.
When 4DL CA, execute 24 to 28
24. Execute BANDWIDTH_SCC3 20MHZ to set Common Parameter – SCC3 – Channel Bandwidth to 20 MHz.
25. Execute DLCHAN_SCC3 1773 to set Common Parameter – SCC3 – DL Channel to 1575.
26. Execute OLVL_EPRE_SCC3 -70.0 to set Common Parameter – SCC3 – Output Level(EPRE) to –70.0 dBm/15
kHz.
27. Execute DLRB_SCC3 100,0 to set Common Parameter – SCC3 – DL RMC - Number of RB to 100, and
Common Parameter – SCC3 – DL RMC – Starting RB to 0.
28. Execute DLIMCS1_SCC2 28, DLIMCS2_SCC2 28 and DLIMCS3_SCC2 28 to set All of Common Parameter -
SCC2 – DL RMC – MCS Index1/2/3 to 28.
29. Execute SERVERIP 192,168,20,10 to set Call Processing Parameter - Packet - Server IP Address to
192.168.20.10.
30. Execute CLIENTIP 192,168,20,11 to set Call Processing Parameter - Packet - Client IP Address 1 to
192.168.20.11.
31. Execute CLIENTIP2 192,168,20,12 to set Call Processing Parameter - Packet - Client IP Address 2 to
192.168.20.12.
32. Execute DEDEPSACT ON to set Call Processing Parameter - Packet - Dedicated EPS Bearer Activation to On.