EasyManuals Logo
Home>Cisco>Network Router>ASR 1000

Cisco ASR 1000 Configuration Guide

Cisco ASR 1000
442 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #249 background imageLoading...
Page #249 background image
16-7
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide
OL-14127-08
Chapter 16 Configuring the 2-Port and 4-Port Channelized T3 SPAs
Configuration Tasks
0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 applique, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions alarm present
DSU mode 0, bandwidth 44210 Kbit, scramble 0, VC 0
The following example shows the output for a serial interface for the first T1 on a channelized T3:
Router# show interface serial2/0/1/1:0
serial2/0/1/1:0 is administratively down, line protocol is down
Hardware is SPA-4XCT3/DS0
MTU 1500 bytes, BW 832 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions alarm present
VC 1: timeslot(s): 2-14, Transmitter delay 0, non-inverted data
Specifying the Interface Address on a SPA
SPA interface ports begin numbering with “0” from left to right. Single-port SPAs use only the port
number 0. To configure or monitor SPA interfaces, you need to specify the physical location of the SIP,
SPA, and interface in the CLI. The interface address format is slot/subslot/port, where:
slot—Specifies the chassis slot number in the Cisco ASR 1000 Series Routers where the SIP is
installed.
subslot—Specifies the slot of the SIP where the SPA is installed.
port—Specifies the number of the individual interface port on a SPA.
The following example shows how to specify the first interface (0) on a SPA installed in the first subslot
of a SIP (0) installed in chassis slot 2:
Router(config)# interface serial 2/0/0
This command shows a serial SPA as a representative example, however the same slot/subslot/port
format is similarly used for other SPAs (such as ATM and POS) and other non-channelized SPAs.

Table of Contents

Other manuals for Cisco ASR 1000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco ASR 1000 and is the answer not in the manual?

Cisco ASR 1000 Specifications

General IconGeneral
BrandCisco
ModelASR 1000
CategoryNetwork Router
LanguageEnglish

Related product manuals