Cisco ASR 1000 Configuration Guide

26-5
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide
OL-14127-08
Chapter 26 Upgrading Field-Programmable Devices
Optional FPD Procedures
During an automatic upgrade, the Cisco ASR 1000 Series Routers will upgrade as many FPDs as
possible at a time. No user intervention is possible or necessary. The upgrade process will not stop until
all FPD images have been updated.
During manual upgrades, it is important to note that users can only specify upgrades for a single piece
of hardware each time the upgrade hw-module subslot [slot-number/subslot-number] command is
entered. The maximum of three simultaneous upgrades applies to manual upgrades as well. If you
individually specify multiple manual FPD upgrades, only three FPDs can be upgraded simultaneously
and that can only occur when the hardware is in different router slots. The FPD upgrade process will stop
when all FPDs for the specified hardware have been upgraded.
Displaying Current and Minimum Required FPD Image Versions
To display the current version of FPD images on the SPAs installed on your router, use the show
hw-module [slot-number/subslot-number | all] fpd command, where slot-number is the slot number
where the SIP is installed, and subslot-number is the number of the SIP subslot where a target SPA is
located. Entering the all keyword shows information for hardware in all router slots.
The following examples show the output when using this show command.
The output display in this example shows that FPD versions on the SPAs in the system meet the minimum
requirements:
Router# show hw-module all fpd
==== ====================== ====== =============================================
H/W Field Programmable Current Min. Required
Slot Card Type Ver. Device: "ID-Name" Version Version
==== ====================== ====== ================== =========== ==============
0/0 SPA-5X1GE-V2 1.1 1-GE I/O FPGA 1.10 1.10
---- ---------------------- ------ ------------------ ----------- --------------
0/1 SPA-8X1FE-TX-V2 1.1 1-FE I/O FPGA 1.1 1.1
---- ---------------------- ------ ------------------ ----------- --------------
0/2 SPA-2XCT3/DS0 1.1 1-ROMMON 2.12 2.12
2-I/O FPGA 2.7 2.7
3-T3 SUBRATE FPGA 1.4 1.4
---- ---------------------- ------ ------------------ ----------- --------------
1/0 SPA-2XOC3-POS 1.0 1-I/O FPGA 3.4 3.4
---- ---------------------- ------ ------------------ ----------- --------------
1/1 SPA-8XCHT1/E1 1.1 1-ROMMON 2.12 2.12
2-I/O FPGA 2.7 2.7
---- ---------------------- ------ ------------------ ----------- --------------
1/2 SPA-2XT3/E3 1.0 1-ROMMON 2.12 2.12
2-I/O FPGA 1.0 1.0
3-E3 FPGA 1.4 1.4
4-T3 FPGA 1.4 1.4
==== ====================== ====== =============================================
This example shows the output when using the slot-number/subslot-number argument to identify a
particular SPA:
Router# show hw-module subslot 1/0 fpd
==== ====================== ====== =============================================
H/W Field Programmable Current Min. Required
Slot Card Type Ver. Device: "ID-Name" Version Version
==== ====================== ====== ================== =========== ==============
1/0 SPA-2XOC3-POS 1.0 1-I/O FPGA 3.4 3.4
==== ====================== ====== =============================================

Cisco ASR 1000 Specifications

General

Brand	Cisco
Model	ASR 1000
Category	Network Router
Language	English