Cisco ASR 1000 Configuration Guide

5
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide
OL-14127-08
Troubleshooting the SIP
Preparing for Online Insertion and Removal of the SIP and SPAs
0/1 SPA-8X1FE-TX-V2 ok 03:18:28
0/2 SPA-2XCT3/DS0 ok 03:18:19
1 ASR1000-SIP10 ok 03:19:46
1/0 SPA-2XOC3-POS ok 03:18:28
1/1 SPA-8XCHT1/E1 ok 03:18:28
1/2 SPA-2XT3/E3 ok 03:18:18
R0 ASR1000-RP1 ok, active 03:19:46
F0 ASR1000-ESP10 ok, active 03:19:46
P0 ASR1006-PWR-AC ok 03:19:14
P1 ASR1006-FAN ok 03:19:14
The following example shows the Cisco ASR 1000-SIP10 installed in slot 0 and Cisco ASR1000-SIP40
installed in slots 1,2,3, and 4 for the Cisco ASR 1013 Router:
Router#show platform
Chassis type: ASR1013
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1000-SIP10 ok 1w0d
1 ASR1000-SIP40 ok 1w0d
1/1 SPA-5X1GE-V2 ok 1w0d
2 ASR1000-SIP40 ok 1w0d
2/1 SPA-1X10GE-L-V2 ok 1w0d
2/3 SPA-1X10GE-L-V2 ok 1w0d
3 ASR1000-SIP40 ok 1w0d
3/3 SPA-4XT3/E3 ok 1w0d
4 ASR1000-SIP40 ok 1w0d
4/2 SPA-5X1GE-V2 ok 1w0d
4/3 SPA-4XCT3/DS0 ok 1w0d
5 ASR1000-SIP40 ok 1w0d
R0 ASR1000-RP2 ok, active 1w0d
R1 ASR1000-RP2 ok, standby 1w0d
F0 ASR1000-ESP40 ok, active 1w0d
P0 ASR1013-PWR-AC ok 1w0d
P1 ASR1013-PWR-AC ps, fail 1w0d
P2 ASR1013-PWR-AC ok 1w0d
P3 ASR1013-PWR-AC ps, fail 1w0d
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 00200800 15.0(1r)S
1 00200800 15.0(1r)S
2 00200800 15.0(1r)S
3 00200800 15.0(1r)S
4 00200800 15.0(1r)S
5 00200800 15.0(1r)S
R0 10021901 15.0(1r)S
R1 10021901 15.0(1r)S
F0 1001270D 15.0(1r)S
Preparing for Online Removal of a SPA
The Cisco ASR 1000 Series Routers support OIR of a SPA independently of removing the SIP. This
means that a SIP can remain installed in the Cisco Aggregation Services Router-1 with one SPA
remaining active, while you remove another SPA from one of the SIP subslots. If you are not planning
to immediately replace a SPA into the SIP, then be sure to install a blank filler plate in the subslot. The
SIP should always be fully installed with either functional SPAs or blank filler plates.
If you are planning to remove a SIP along with its SPAs, then you do not need to follow the instructions
in this section. To remove a SIP, see the
“Preparing for Online Removal of a SIP” section on page 5-3.

Cisco ASR 1000 Specifications

General

Operating System	Cisco IOS XE
Interfaces	10 Gigabit Ethernet
Power Supply	AC or DC
Number of Total Expansion Slots	Varies by model
Management Port	Console
Redundant Power Supply Supported	Yes
Width	17.5 inches
Memory	Varies by model
Storage	Varies by model
Dimensions (H x W x D)	Varies by model
Weight	Varies by model
Operating Temperature	32°F to 104°F (0°C to 40°C)
Humidity	5% to 95% non-condensing
MTBF	Varies by model
Redundancy	Redundant power supplies, fans, and route processors (depending on model)