EasyManuals Logo

Cisco Catalyst 2950 Command Reference

Cisco Catalyst 2950
686 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #459 background imageLoading...
Page #459 background image
2-431
Catalyst 2950 and Catalyst 2955 Switch Command Reference
0L-10102-01
Chapter 2 Catalyst 2950 and 2955 Cisco IOS Commands
snmp-server enable traps
snmp-server enable traps
Use the snmp-server enable traps global configuration command to enable the switch to send Simple
Network Management Protocol (SNMP) notification for various trap types to the network management
system (NMS). Use the no form of this command to return to the default setting.
snmp-server enable traps [alarms | bridge | c2900 | cluster | config | copy-config | entity |
envmon [fan | shutdown | status | supply | temperature | voltage] | flash | hsrp |
mac-notification | port-security [trap-rate value] | rtr | snmp [authentication | coldstart |
linkdown | linkup | warmstart] | stpx | syslog | vlan-membership | vlancreate | vlandelete |
vtp]
no snmp-server enable traps [alarms | bridge | c2900 | cluster | config | copy-config | entity |
envmon [fan | shutdown | status | supply | temperature | voltage] | flash | hsrp |
mac-notification | port-security [trap-rate ] | rtr | snmp [authentication | coldstart |
linkdown | linkup | warmstart]| stpx | syslog | vlan-membership | vlancreate | vlandelete |
vtp]
Syntax Description alarms (Optional) Enable SNMP alarm traps. This keyword is only available on a
Catalyst 2955 switch.
bridge (Optional) Enable SNMP Spanning Tree Protocol (STP) bridge management
information base (MIB) traps.
c2900 (Optional) Enable SNMP configuration traps.
cluster (Optional) Enable cluster traps.
config (Optional) Enable SNMP configuration traps.
copy-config (Optional) Enable SNMP copy-configuration traps.
entity (Optional) Enable SNMP entity traps.
envmon (Optional) Enable environmental monitor (EnvMon) MIB.
fan (Optional) Enable SNMP EnvMon fan traps.
shutdown (Optional) Enable SNMP EnvMon monitor shutdown traps.
status Optional) Enable SNMP EnvMon monitor status change traps.
supply (Optional) Enable SNMP power supply traps.
temperature (Optional) Enable SNMP EnvMon temperature traps.
voltage (Optional) Enable SNMP EnvMon voltage traps.
flash (Optional) Enable SNMP FLASH notifications.
hsrp (Optional) Enable Hot Standby Router Protocol (HSRP) traps.
mac-notification (Optional) Enable MAC address notification traps.
port-security (Optional) Enable port security traps.
trap-rate value (Optional) Set the number of traps per second. The range is 0 to 1000.
rtr (Optional) Enable SNMP Response Time Reporter traps.
snmp (Optional) Enable SNMP traps.
authentication (Optional) Enable SNMP authentication traps.
coldstart (Optional) Enable SNMP coldstart traps.
linkdown (Optional) Enable SNMP linkdown traps.

Table of Contents

Other manuals for Cisco Catalyst 2950

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 2950 and is the answer not in the manual?

Cisco Catalyst 2950 Specifications

General IconGeneral
Forwarding Bandwidth8.8 Gbps
Switching Capacity13.6 Gbps
Forwarding Rate6.6 Mpps
Weight3.6 kg
RAM16 MB
Flash Memory8 MB
Operating Humidity10% to 85% non-condensing
Uplink Ports2 x 10/100/1000Base-T
Dimensions4.4 cm x 44.5 cm x 24.2 cm
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesQuality of Service (QoS), VLAN support
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p
Status Indicatorssystem
Operating Temperature0 to 45°C
Ports24 x 10/100 Ethernet ports
MAC Address Table Size8, 192 entries
Power SupplyInternal 100-240V AC, 50-60Hz

Related product manuals