EasyManuals Logo

Cisco Catalyst 2950 Command Reference

Cisco Catalyst 2950
686 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #140 background imageLoading...
Page #140 background image
2-110
Catalyst 2950 and Catalyst 2955 Switch Command Reference
OL-10102-01
Chapter 2 Catalyst 2950 and 2955 Cisco IOS Commands
errdisable detect cause
errdisable detect cause
Use the errdisable detect global configuration command to enable error disable detection. Use the no
form of this command to disable this feature.
errdisable detect cause {all | dhcp-rate-limit | dtp-flap | gbic-invalid | link-flap | loopback |
pagp-flap | vmps}
no errdisable detect cause {all | dhcp-rate-limit | dtp-flap | gbic-invalid | link-flap | loopback |
pagp-flap | vmps}
Syntax Description
Defaults The default is all, enabled for all causes.
Command Modes Global configuration
Command History
Usage Guidelines A cause (for example, dtp-flap) is the reason why the error-disabled state occurred. When a cause is
detected on an interface, the interface is placed in error-disabled state, an operational state similar to
link-down state. If you do not enable errdisable recovery for the cause, the interface stays in the
error-disabled state until you enter the shutdown and no shutdown interface configuration commands.
If you enable the recovery for a cause, the interface is brought out of the error-disabled state and allowed
to retry the operation again when all the causes have timed out.
You must enter the shutdown and then the no shutdown commands to manually recover an interface
from the error-disabled state.
all Enable detection for all error disable causes.
dhcp-rate-limit Enable detection for the DHCP cause.
dtp-flap Enable detection for the Dynamic Trunking Protocol (DTP)-flap cause.
gbic-invalid Enable error detection for an invalid GBIC error-disable cause.
link-flap Enable detection for the link flap cause.
loopback Enable detection for the loopback cause.
pagp-flap Enable detection for the Port Aggregation Protocol (PAgP)-flap cause.
vmps Enable error detection for the VLAN Membership Policy Server (VMPS).
Release Modification
12.1(6)EA2 This command was introduced.
12.1(9)EA1 The bpduguard, rootguard, and udld keywords were removed. The
gbic-invalid keyword was added.
12.1(19)EA1 The dhcp-rate-limit and loopback keywords were added.
12.1(14)EA1 The loopback keyword was added.

Table of Contents

Other manuals for Cisco Catalyst 2950

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 2950 and is the answer not in the manual?

Cisco Catalyst 2950 Specifications

General IconGeneral
Forwarding Bandwidth8.8 Gbps
Switching Capacity13.6 Gbps
Forwarding Rate6.6 Mpps
Weight3.6 kg
RAM16 MB
Flash Memory8 MB
Operating Humidity10% to 85% non-condensing
Uplink Ports2 x 10/100/1000Base-T
Dimensions4.4 cm x 44.5 cm x 24.2 cm
Remote Management ProtocolSNMP, Telnet, HTTP
FeaturesQuality of Service (QoS), VLAN support
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p
Status Indicatorssystem
Operating Temperature0 to 45°C
Ports24 x 10/100 Ethernet ports
MAC Address Table Size8, 192 entries
Power SupplyInternal 100-240V AC, 50-60Hz

Related product manuals