DigiDesign D-Show Profile - Stage Rack Back Panel

To Next Page

To Previous Page

D-Show Proﬁle Guide252

Stage Rack Back Panel

Power Switch

The Power switch applies power to the Stage Rack.

AC Power Connector

The AC Power connector accepts a standard AC power cable.

Stage Rack power supplies are auto-power selecting (100V to

240V) and automatically work with a standard modular power

cord when connected to an AC receptacle in any country.

Figure 23. Stage Rack back panel

STAGE

DO NOT OBSTRUCT FANS

Power switch

Power connector

Main Page

Default Chapter3
- Table of Contents3
Part I Overview and Installation11
Chapter 1. D-Show Profile System Introduction13
- D-Show Profile Features13
- D-Show System Components13
- D-Show Expansion Options14
- Operational Requirements15
- Connection Requirements15
Chapter 2. Configuring and Connecting D-Show17
- Unpacking and Assembling D-Show Profile17
- Assembling and Attaching the Video Monitor Mount to D-Show Profile17
- Back Panel Connectors19
- Connecting D-Show Components20
- Connecting a Second Stage Rack23
- Power Connections24
- Audio and MIDI Connections24
- Control Surface Connections29
- Powering up the System30
- Powering down the System30
- Restarting the System30
- Setting the System Clock30
- Enabling a Second Stage Rack31
Part II System Description33
Chapter 3. D-Show Profile Control Overview35
- D-Show Profile Top Panel35
- Input Channels and Faders36
- Assignable Channel Section40
- Output Masters42
- Master and Global Controls43
- Meters44
Chapter 4. Basic Commands and Modes45
- Control Overview45
- Config Mode and Show Mode46
- Global Modifier Switches46
- Software Screen Pages and Tabs47
Chapter 5. Navigating and Selecting Channels51
- Banking Input Channels and FX Returns51
- Banking Graphic EQ Frequency Bands51
- Banking the Output Section52
- Selecting and Targeting Channels52
- Targeting Plug-In Inserts53
- Screen Controls and Shortcuts54
- Input Channel Presets56
Chapter 6. Options59
- Overview of Options59
- System59
- Devices61
- Other D-Show Options62
Part III Signal Routing67
Chapter 7. Inputs and Input Routing69
- Configuring Inputs69
- Assigning Inputs to Channels70
- Routing Channels to Busses71
- Routing Inputs to Direct Outputs73
- Using Built-In Dynamics and EQ73
- Using Inserts on Channels74
- Using Input Direct75
- Adjusting Input Controls75
Chapter 8. Outputs and Output Routing79
- Configuring Outputs79
- Routing Busses to Hardware Outputs81
- Routing Group Outputs to the Main Busses81
- Using Inserts on Output Busses82
- Inserting the Built-In Graphic EQ on Output Busses83
- Adjusting Output Controls84
- Adjusting Main Bus Controls85
- Monitoring the Main MIX86
- Direct Outputs86
- Matrix Mixers87
- Personal Q Mixers87
- Assigning and Using Vcas87
Chapter 9. Groups89
- Configuring Group Busses89
- Assigning Inputs to Group Busses89
- Routing Group Outputs to the Main Busses89
- Routing Group Busses90
- Managing Group Bus Assignments90
- Group Bus Signal Flow Options91
- Adjusting Group Bus Output Controls92
- Simple and Expert Operational Modes92
Chapter 10. Auxes and Variable Groups95
- Configuring Aux Busses and Variable Group Busses95
- Assigning Inputs to Aux Busses and Variable Group Busses97
- Routing Aux and Variable Group Busses to Outputs and Plug-Ins98
- Adjusting Aux and Variable Group Output Controls99
- Managing Aux Bus and Variable Group Bus Assignments100
Chapter 11. Matrix Mixers and PQ Mixers103
- Matrix Mixers103
- Personal Q Mixers104
- Configuring Matrix and PQ Mixers104
- Adjusting Matrix Mixer and PQ Mixer Input Controls106
- Adjusting Matrix Mixer and PQ Mixer Output Controls108
- Adjusting Other Matrix and PQ Output Controls108
- Working with a PQ Controller109
- Snapshot Data and Parameters for Matrix and PQ Mixers109
Chapter 12. Patchbay111
- Accessing the Patchbay111
- Overview of the Patchbay111
- Navigating the Patchbay113
- Routing Channels in the Patchbay114
- Warning When Stealing Inputs or Outputs in the Patchbay116
Chapter 13. Metering117
- Channel Meters117
- ACS Input and Dynamics Meters118
- Meter Bridge119
- Metering Options120
Chapter 14. Solo and Monitor Busses121
- Solo Bus Modes121
- Solo Operation Options122
- Solo Bus Operation123
- Solo Safing Channels124
- Monitor Bus Operation124
- Talkback, 2-Track and Oscillator Controls126
Chapter 15. Muting and Mute Groups131
- Muting131
- Mute Groups132
- Function Switches133
Part IV Processing135
Chapter 16. Dynamics137
- Built-In Compressor/Limiter137
- Built-In Expander/Gate138
- Channel Modes Affecting Dynamics139
- Adjusting Dynamics139
- Dynamics Settings and Presets141
- Side-Chain Keys and Filters142
Chapter 17. EQ145
- Built-In EQ Parameters145
- Channel Modes Affecting EQ146
- Adjusting EQ147
- Graphic EQ for Outputs149
- Adjusting EQ Plug-Ins150
- EQ Settings and Presets150
Chapter 18. Hardware Inserts153
- Connecting External Effects Units153
- Assigning Hardware Inserts to Channels154
Chapter 19. Plug-Ins155
- Installing and Authorizing Plug-Ins155
- Overview of Plug-Ins158
- Plug-In Racks159
- Rack Slots161
- Assigning and Routing Plug-Ins162
- Adjusting Plug-Ins165
- Adjusting EQ and Dynamics Plug-Ins from the ACS167
- Plug-In Presets and Snapshots168
- Plug-In DSP Usage169
- Plug-In Levels170
- Plug-In Latency and Processing Delay170
Part V Shows171
Chapter 20. Shows and File Management173
- Creating Shows173
- Loading Shows174
- Working with Presets175
- Transferring Settings, Shows and Presets177
- Undoing Changes Using the History Feature178
Chapter 21. Snapshots181
- Snapshots Page181
- Snapshot Controls on the D-Show Profile Control Surface184
- Snapshots List184
- Creating Snapshots186
- Recalling Snapshots187
- Recall Safe and Channel Automation Safe188
- Managing Snapshots192
- Making Changes to Snapshots194
- Preview Mode195
- Undoing Snapshot Commands198
- Disabling Snapshots198
- Adding MIDI Messages to Snapshots199
- Adding Plug-In Data to Snapshots200
- Snapshot Options201
- Snapshot Data Types and Parameters203
Chapter 22. Events205
- Introduction205
- The Events Window206
- Creating Events208
- Creating Triggers210
- Creating Actions211
- Testing Events212
- Resetting Events213
- Snapshots and Events213
- Default Settings, Templates and Examples214
- Events and Show File Compatibility215
- Trigger Types216
- Action Types217
Chapter 23. Synchronization219
- Automating Recall of Snapshots with MIDI Time Code219
- Remote Control of Snapshot Recall221
- Triggering of External Devices on Snapshot Recall222
- Sending MIDI Messages on Snapshot Recall222
- Synchronizing with Word Clock and Digital Audio Input222
Chapter 24. Using the D-Show Standalone Software223
- System Requirements223
- Installing the D-Show Standalone Software223
- Simulating a D-Show Configuration224
- Transfer and Filing Quick Start224
- Exporting Patchbay Names to Text226
Part VI Specifications227
Chapter 25. Mechanical Specifications229
Chapter 26. Audio Specifications231
- D-Show Profile Console231
- Stage Rack232
- FOH Rack232
- Snake234
Chapter 27. Signal Flow Diagrams235
- D-Show Input Signal Flow Diagram235
- D-Show Output Signal Flow Diagram236
Chapter 28. Troubleshooting237
- Problem Solving237
- In Case of System Failure239
- Restarting D-Show241
- Hardware Monitoring Window242
- Resetting Hardware Components242
- Using the System Restore CD to Update or Restore the System243
- D-Show Profile Power and Status Leds244
Part VII Reference245
Chapter 29. Control Surface Reference247
- D-Show Profile Console247
- GPI (General Purpose Interface)248
- GPI Wiring Diagrams250
Chapter 30. FOH Rack Reference253
- FOH Rack Front Panel253
- FOH Rack Back Panel254
- FOH Link Cable256
Chapter 31. Stage Rack Reference259
- Stage Rack Front Panel259
- Stage Rack Back Panel262
Index263

DigiDesign D-Show Profile - Stage Rack Back Panel

Table of Contents

Related product manuals